Code	Definition
0	NOT ESTABLISHED.
1	SUITABLE FOR COMPETITIVE ACQUISITION. (SEE NOTES 1 AND 2.)
2	SUITABLE FOR COMPETITIVE ACQUISITION FOR THE FIRST. TIME. (SEE NOTES 1 AND 2.)
3	ACQUIRE DIRECTLY FROM THE ACTUAL MANUFACTURER, WHETHER OR NOT THE PRIME CONTRACTOR IS THE ACTUAL MANUFACTURER.
4	ACQUIRE, FOR THE FIRST TIME, DIRECTLY FROM THE ACTUAL MANUFACTURER RATHER THAN THE PRIME CONTRACTOR WHO IS NOT THE ACTUAL MANUFACTURER.
5	ACQUIRE ONLY FROM THE PRIME CONTRACTOR ALTHOUGH THE ENGINEERING DATA IDENTIFIES THE COMMERCIAL AND GOVERNMENT ENTITY CODE (CAGE) AND PART NUMBER OF A SOURCE OTHER THAN THE PRIME CONTRACTOR. (SEE NOTE 3.)

Code	Definition
0	NOT ESTABLISHED
A	THE GOVERNMENT'S RIGHTS TO USE DATA IN ITS POSSESSION IS QUESTIONABLE. (NOTE: THIS CODE IS ONLY APPLICABLE TO PARTS UNDER IMMEDIATE BUY REQUIREMENTS AND ONLY AS LONG AS RIGHTS TO DATA ARE STILL UNDER REVIEW FOR RESOLUTION AND APPROPRIATE RECODING.) VALID AMCS: 1, 2, 3, 4 AND 5.
B	ACQUISITION OF THIS PART IS RESTRICTED TO SOURCE(S) SPECIFIED ON "SOURCE CONTROL", "ALTERED ITEM" OR "SELECTED ITEM" DRAWINGS/DOCUMENTS. VALID AMCS: 1, 2, 3, 4 AND 5.
C	THIS PART REQUIRES ENGINEERING SOURCE APPROVAL BY THE DESIGN CONTROL ACTIVITY IN ORDER TO MAINTAIN THE QUALITY OF THE PART. AN ALTERNATE SOURCE MUST QUALIFY IN ACCORDANCE WITH THE DESIGN CONTROL ACTIVITY'S PROCEDURES, AS APPROVED BY THE COGNIZANT GOVERNMENT ENGINEERING ACTIVITY. VALID AMCS: 1, 2, 3, 4 AND 5.
D	THE DATA NEEDED TO PRODUCE THIS ITEM FROM ADDITIONAL SOURCES IS NOT PHYSICALLY AVAILABLE. VALID AMCS: 3, 4 AND 5.
G	THE GOVERNMENT HAS UNLIMITED RIGHTS TO THE TECHNICAL DATA, AND THE DATA PACKAGE IS COMPLETE. VALID AMCS: 1 AND 2.
H	THE GOVERNMENT PHYSICALLY DOES NOT HAVE IN ITS POSSESSION SUFFICIENT, ACCURATE, OR LEGIBLE DATA TO PURCHASE THIS PART FROM OTHER THAN CURRENT SOURCE(S). (NOTE: THIS CODE IS APPLICABLE ONLY TO PARTS UNDER IMMEDIATE BUY REQUIREMENTS AND ONLY AS LONG AS THE DEFICIENCY IS UNDER REVIEW FOR RESOLUTION AND APPROPRIATE RECODING.) VALID AMCS: 1, 2, 3, 4 AND 5.
K	THIS PART MUST BE PRODUCED FROM CLASS 1A CASTINGS (E.G., CLASS 1 OF MIL-C-6021) AND SIMILAR TYPE FORGINGS. THE PART MUST BE PROCURED ONLY FROM SOURCES WHICH USE CASTINGS OR FORGINGS OBTAINED FROM APPROVED (CONTROLLED) SOURCE(S). VALID AMCS: 1, 2, 3, 4 AND 5.
L	THE ANNUAL BUY VALUE OF THIS PART FALLS BELOW THE SCREENING THRESHOLD OF $10,000 BUT IT HAS BEEN SCREENED FOR KNOWN SOURCE(S). (NOTE: THIS CODE SHALL NOT BE USED WHEN SCREENING PARTS ENTERING THE INVENTORY. IT SHALL NOT BE ASSIGNED IN PREFERENCE TO OR SUPERSEDE ANY OTHER AMSC.) VALID AMCS: 1, 2, 3, 4 AND 5.
M	MASTER OR COORDINATED TOOLING IS REQUIRED TO PRODUCE THIS PART. THIS TOOLING IS NOT OWNED BY THE GOVERNMENT OR, WHERE OWNED, CANNOT BE MADE AVAILABLE TO OTHER SOURCES. VALID AMCS: 1, 2, 3, 4, AND 5.
N	THIS PART REQUIRES SPECIAL TEST AND/OR INSPECTION FACILITIES TO DETERMINE AND MAINTAIN ULTRA- PRECISION QUALITY FOR ITS FUNCTION OR SYSTEM INTEGRITY. SUBSTANTIATION AND INSPECTION OF THE PRECISION OR QUALITY CANNOT BE ACCOMPLISHED WITHOUT SUCH SPECIALIZED TEST OR INSPECTION FACILITIES. VALID AMCS: 1, 2, 3, 4 AND 5.
P	THE RIGHTS TO USE THE DATA NEEDED TO PURCHASE THIS PART FROM ADDITIONAL SOURCES ARE NOT OWNED BY THE GOVERNMENT AND CANNOT BE PURCHASED. VALID AMCS: 1, 2, 3, 4 AND 5.
Q	THE GOVERNMENT DOES NOT HAVE ADEQUATE DATA, LACKS RIGHTS TO DATA, OR BOTH, NEEDED TO PURCHASE THIS PART FROM ADDITIONAL SOURCES. VALID AMCS: 1, 2, 3, 4 AND 5.
R	THE DATA OR THE RIGHTS TO USE THE DATA NEEDED TO PURCHASE THIS PART FROM ADDITIONAL SOURCES ARE NOT OWNED BY THE GOVERNMENT AND IT HAS BEEN DETERMINED THAT IT IS UNECONOMICAL TO PURCHASE THEM. VALID AMCS: 1, 2, 3, 4 AND 5.
S	PROCUREMENT OF THIS ITEM RESTRICTED TO LIMITED SOURCE(S) BECAUSE SECURITY CLASSIFIATION OF CONFIDENTIAL OR HIGHER PREVENTS PUBLIC DISCLOSURE. VALID AMCS: 1, 2, 3, 4 AND 5.
T	ACQUISITION OF THIS PART IS CONTROLLED BY QPL PROCEDURES. VALID AMCS: 1 AND 2.
U	THE COST TO THE GOVERNMENT TO BREAKOUT THIS PART AND ACQUIRE IT COMPETITIVELY HAS BEEN DETERMINED TO EXCEED THE PROJECTED SAVINGS OVER THE LIFE SPAN OF THE PART. VALID AMCS: 1, 2, 3, 4 AND 5.
V	THIS PART HAS BEEN DESIGNATED A HIGH-RELIABILITY PART UNDER A FORMAL RELIABILITY PROGRAM. PROBABILITY OF FAILURE WOULD BE UNACCEPTABLE FROM THE STANDPOINT OF SAFETY OF PERSONNEL AND/OR EQUIPMENT. THE COGNIZANT ENGINEERING ACTIVITY HAS DETERMINED THAT DATA TO DEFINE AND CONTROL RELIABILITY LIMITS CANNOT BE OBTAINED NOR IS IT POSSIBLE TO DRAFT ADEQUATE SPECIFICATIONS FOR THIS PURPOSE. VALID AMCS: 1, 2, 3, 4 AND 5.
Y	THE DESIGN OF THIS PART IS UNSTABLE. ENGINEERING, MANUFACTURING, OR PERFORMANCE CHARACTERISTICS INDICATE THAT THE REQUIRED DESIGN OBJECTIVES HAVE NOT BEEN ACHIEVED. MAJOR CHANGES ARE CONTEMPLATED BECAUSE THE PART HAS A LOW PROCESS YIELD OR HAS DEMONSTRATED MARGINAL PERFORMANCE DURING TESTS OR SERVICE USE. THESE CHANGES WILL RENDER THE PRESENT PART OBSOLETE AND UNUSABLE IN ITS PRESENT CONFIGURATION. LIMITED ACQUISITION FROM THE PRESENT SOURCE IS ANTICIPATED PENDING CONFIGURATION CHANGES. VALID AMCS: 1, 2, 3, 4 AND 5.
Z	THIS PART IS A COMMERCIAL/NON-DEVELOPMENTAL/OFF-THE-SHELF-ITEM. VALID AMCS: 1, 2, 3, 4 AND 5.

Code	Definition
0	DLIS FILES CONVERSION CODE. THIS CODE WAS ASSIGNED BY DLIS TO EXISTING WHOLESALE INTERSERVICE SUPPLY SUPPORT AGREEMENT (WISSA) TYPE RECORDING (LOA 8D) DURING INITIAL FILE CONVERSION PROGRAM. THIS CODE IS REASSIGNED TO CODE 1,2,3,5,6 OR 8 UPON COMPLETION OF ITEM REVIEW. THE SICA CMD WILL REFLECT THE SOS/SOSM AND AAC COMPATIBLE WITH THE PICA. THE PICA WILL NOT BE ENTERED IN THE DAAS IMM FIELD.
1	EXCEPTION ITEM (END ITEM OF EQUIPMENT). THIS CODE IDENTIFIES SICA MANAGED END ITEMS OF EQUIPMENT ASSIGNED TO ANOTHER SERVICE PICA THAT IS RESPONSIBLE FOR THE WHOLESALE LOGISTICS SUPPORT FUNCTIONS OF SINGLE SUBMITER OF CATALOGING DATA, ACQUISITION AND DISPOSAL AUTHORITY. SUPPLY SUPPORT REQUIREMENTS WILL BE SUBMITTED BY THE SICA TO THE PICA ON MILITARY INTERDEPARTMENTAL PURCHASE REQUESTS (MIPRS) UNLESS OTHERWISE DIRECTED BY THE PICA. THE SICA IS RESPONSIBLE FOR THE WHOLESALE STOCK, STORE, AND ISSUE FUNCTIONS, IN SUPPORT OF SICA ACTIVITIES AND HAS RETAINED DEPOT REPAIR CAPABILITY WHERE APPLICABLE. RETENTION OF DEPOT MAINTENANCE CAPABILITY FOR END ITEMS OF EQUIPMENT REQUIRES DOCUMENTED JUSTIFICATION BY THE SICA TO THE PICA VIA JLC FORM 19. IF PICA AND SICA CANNOT REACH AN AGREEMENT THE DOCUMENTATION WILL BE FORWARDED TO THE JOINT MISMOS FOR A DECISION. THE SICA CATALOG MANAGEMENT DATA (CMD) WILL REFLECT SOURCE OF SUPPLY OR SOS MODIFIERS COMPATIBLE WITH THE SICA MANAGING ACTIVITY. THE PICA WILL NOT BE ENTERED IN THE DEFENSE AUTOMATIC ADDRESSING SYSTEM INTEGRATED MATERIEL MANAGER (DAAS IMM) FIELD.
2	EXCEPTION ITEM (DEPOT REPARABLE COMPONENT OR SICA MANAGED CONSUMABLE). THIS CODE IDENTIFIES SICA MANAGED DEPOT REPARABLE COMPONENTS, OR SICA MANAGED CONSUMABLES WHEREIN THE SICA CANNOT USE REPAIRED ITEMS, ASSIGNED TO ANOTHER SERVICE WHICH HAS RESPONSIBILITY FOR THE LOGISTICS FUNCTIONS OF SINGLE SUBMITTER OF CATALOGING DATA, ACQUISITION AND DISPOSAL AUTHORITY. SUPPLY SUPPORT REQUIREMENTS WILL BE SUBMITTED BY THE SICA TO THE PICA ON MIPRS UNLESS OTHERWISE DIRECTED BY PICA. THE SICA SERVICE HAS RETAINED THE WHOLESALE STOCK, STORE, AND ISSUE FUNCTIONS IN SUPPORT OF SICA ACTIVITIES AND HAS RETAINED DEPOT REPAIR CAPABILITY, WHERE APPLICABLE. RETENTION OF DEPOT MAINTENANCE CAPABILITY FOR THE DEPOT REPARABLE COMPONENTS REQUIRES DOCUMENTED JUSTIFICATION BY THE SICA TO THE PICA VIA JLC FORM 9. IF THE PICA AND SICA CANNOT REACH AN AGREEMENT, THE DOCUMENTATION WILL BE FORWARDED TO THE JOINT MISMOS FOR A DECISION. THE SICA CMD WILL REFLECT SOURCE OF SUPPLY OR SOS MODIFIERS COMPATIBLE WITH THE SICA MANAGING ACTIVITY. THE PICA WILL NOT BE ENTERED IN THE DAAS IMM FIELD.
3	END ITEM PRIMARY INVENTORY CONTROL ACTIVITY. THIS CODE IDENTIFIES SICA MANAGED END ITEMS OF EQUIPMENT ASSIGNED TO ANOTHER SERVICE PICA THAT IS RESPONSIBLE FOR THE WHOLESALE LOGISTICS SUPPORT FUNCTIONS OF SINGLE SUBMITTER OF CATALOGING DATA, ACQUISITION AND DISPOSAL AUTHORITY AND DEPOT MAINTENANCE, IF REQUIRED, TO BE PROVIDED BY DMISA. SUPPLY SUPPORT REQUIREMENTS WILL BE SUBMITTED BY THE SICA TO THE PICA ON MIPRS UNLESS OTHERWISE DIRECTED BY THE PICA. THE SICA IS RESPONSIBLE FOR THE WHOLESALE STOCK, STORE, AND ISSUE FUNCTIONS FOR SICA ACTIVITIES. THE SICA CMD WILL REFLECT SOURCE OF SUPPLY OR SOS MODIFIERS COMPATIBLE WITH THE SICA MANAGING ACTIVITY. THE PICA WILL NOT BE ENTRERED IN THE DAAS IMM FIELD.
4	DEPOT REPARABLE COMPONENT (TYPE I TEMPORARY). THIS CODE IDENTIFIES SICA MANAGED DEPOT REPARABLE COMPONENTS ASSIGNED TO ANOTHER SERVICE PICA THAT IS RESPONSIBLE FOR THE LOGISTICS FUNCTIONS OF SINGLE SUBMITTER OF CATALOGING DATA, ACQUISITION AND DISPOSAL AUTHORITY AND DEPOT MAINTENANCE TO BE PROVIDED BY DMISA. SUPPLY SUPPORT REQUIREMENTS WILL BE SUBMITTED BY THE SICA TO THE PICA ON MIPRS UNLESS OTHERWISE DIRECTED BY THE PICA. THE SICA IS RESPONSIBLE FOR THE WHOLESALE STOCK, STORE, AND ISSUE FUNCTIONS FOR SICA ACTIVITIES. THIS CODE IS TEMPORARILY ASIGNED TO ITEMS WHICH HAVE NOT COMPLETED PHRASE II ITEM REVIEW PROCESSING. THE SICA CMD WILL REFLECT SOURCE OF SUPPLY OR SOS MODIFIERS COMPATIBLE WITH THE SICA MANAGING ACTIVITY. THE PICA WILL NOT BE ENTERED IN THE DAAS IMM FIELD.
5	DEPOT REPARABLE COMPONENT (TYPE II). THIS CODE IDENTIFIES SICA MANAGED DEPOT REPARABLE COMPONENTS ASSIGNED TO ANOTHER SERVICE WHICH IS RESPONSIBLE FOR THE LOGISTICS FUNCTIONS OF SINGLE SUBMITTER CATALOGER, ACQUISITION AND DISPOSAL AUTHORITY, DEPOT MAINTENANCE, AND PERFORMS THE WHOLESALE STOCK, STORE, AND ISSUE FUNCTIONS AND ESTABLISHES, BUDGETS AND FUNDS THE WHOLESALE STOCK LEVEL REQUIREMENT. SUPPLY REQUIREMENTS WILL BE SUBMITTED TO THE PICA ON REQUISITIONS WHICH ARE FUNDED BY A DESIGNATED POINT WITHIN THE SICA. UNSERVICEABLE SICA ASSETS WILL NORMALLY BE RETURNED TO THE PICA FOR CREDIT. THE SICA WILL PROVIDE ITEM/PROGRAM DATA REQUIRED BY THE PICA TO MEET THE MATERIEL SUPPORT COMMITMENTS. NORMALLY, MILITARY INTERDEPARTMENTAL PURCHASE REQUESTS (MIPR) WILL NOT BE REQUESTED BY THE PICA TO SUPPORT SICA NIMSC 5 REQUIREMENTS. THE SICA CMD WILL REFLECT SOURCE OF SUPPLY OR SOS MODIFIERS COMPATIBLE WITH THE SICA MANAGING ACTIVITY. THE PICA WILL NOT BE ENTERED IN THE DAAS IMM FIELD.
6	REQUISITIONING ACTIVITY FUNDED ITEMS. THIS CODE IDENTIFIES ITEMS WHEREIN SICA ACTIVITIES HAVE BEEN AUTHORIZED BY THEIR PARENT SERVICE TO SUBMIT REQUISITIONS DIRECTLY TO THE PICA. THESE ITEMS ARE USUALLY MANAGED AS CONSUMABLE (EXPENSE) ITEMS BY THE SICA SERVICE. THE SICA CMD WILL REFLECT THE SOURCE OF SUPPLY OR SOURCE OF SUPPLY MODIFIERS COMPATIBLE WITH THE PICA MANAGING ACTIVITIES AND MAY REFLECT THE ACQUISITION ADVICE CODE (AAC) OF THE PICA. THE PICA WILL NOT BE ENTERED IN THE DAAS IMM FIELD.
7	JOINT CONVENTIONAL AMMUNITION PRODUCTION (JCAP) COGNIZANCE. THIS ITEM IS UNDER JCAP COGNIZANCE AND SUPPLY SUPPORT WILL BE DETERMINED BY THE DOD SINGLE MANAGER FOR CONVENTIONAL AMMUNITION. PROVISION OF THIS REGULATION WILL NOT APPLY. THE SICA CMD WILL REFLECT SOURCE OF SUPPLY OR SOURCE OF SUPPLY MODIFIER CODES COMPATIBLE WITH THE SICA MANAGING ACTIVITY. THE PICA WILL NOT BE ENTERED IN THE DAAS IMM FIELD.
8	DEPOT REPARABLE COMPONENT (TYPE I). THIS CODE IDENTIFIES SICA MANAGED DEPOT REPARABLE COMPONENTS WHICH HAVE BEEN REVIEWED FOR MIGRATION TO TYPE II, BUT WILL BE RETAINED UNDER TYPE I MANAGEMENT. THE PICA WILL HAVE RESPONSIBILITY FOR THE LOGISTICS FUNCTIONS OF SINGLE SUBMITTER OF CATALOGING DATA, ACQUISITION AND DISPOSAL AUTHORITY, AND DEPOT MAINTENANCE TO BE PROVIDED BY DMISA.SUPPLY SUPPORT REQUIREMENTS WILL BE SUBMITTED BY THE SICA TO THE PICA VIA MIPRS UNLESS OTHERWISE DIRECTED BY THE PICA. THE SICA IS RESPONSIBLE FOR WHOLESALE STOCK, STORE, AND ISSUE FUNCTIONS FOR SICA ACTIVITIES. THE SICA SOURCE OFSUPPLY/SOURCE OF SUPPLY MODIFIER AND ACQUISITION ADVICE CODE WILL APPEAR IN THE SICA CMD. THE PICA WILL NOT BE ENTERED IN THE DAAS IMM FIELD.
9	EXCEPTION ITEM (DEPOT MAINTENANCE REVIEW NOT COMPLETED). THIS CODE IDENTIFIES ITEMS WHEREIN ASSIGNMENT FOR DEPOT REPAIR HAS NOT BEEN ESTABLISHED. PICA RESPONSIBILITIES ARE LIMITED TO SINGLE SUBMITTER OF CATALOGING DATA, ACQUISITION AND DISPOSAL AUTHORITY. UPON COMPLETION OF DEPOT MAINTENANCE REVIEW, AND ASSIGNMENT FOR DEPOT REPAIR IS MADE, CODE 9 ITEMS WILL BE REASSIGNED TO CODE 1, 2, 3, 5, 6, OR 8. THE SICA CMD WILL REFLECT THE SOURCE OF SUPPLY OR SOS MODIFIERS COMPATIBLE WITH THE SICA MANAGING ACTIVITIES. THE PICA WILL NOT BE ENTERED IN THE DAAS IMM FIELD.
A	AN ACTIVITY WITHIN THE ARMY IS PROVIDING DEPOT MAINTENANCE SUPPORT.
B	MULTI-SERVICE ORGANIC REPAIR. THE DEPOT REPAIR REQUIREMENT OF TWO OR MORE SERVICES IS BEING PERFORMED ORGANICALLY BY MORE THAN ONE SERVICE.
D	DLA/DGSC PROVIDES DEPOT MAINTENANCE SUPPORT
E	EXCESS OVERFLOW WHICH IS CONTRACTED BY THE PICA.
F	AN ACTIVITY WITHIN THE AIR FORCE IS PROVIDING DEPOT MAINTENANCE SUPPORT.
G	A GSA ACTIVITY IS PROVIDING DEPOT MAINTENANCE SUPPORT.
J	JCAP COGNIZANCE. THIS ITEM IS UNDER JCAP COGNIZANCE AND SUPPLY SUPPORT WILL BE DETERMINED BY THE DOD SINGLE MANAGER FOR CONVENTIONAL AMMUNITION. PROVISION OF THIS REGULATION WILL NOT APPLY.
M	AN ACTIVITY WITHIN THE MARINE CORPS IS PROVIDING DEPOT MAINTENANCE SUPPORT.
P	TOTAL DEPOT MAINTENANCE IS BEING ACCOMPLISHED BY COMMERCIAL CONTRACT.
S	ORGANIC OVERFLOW TO ANOTHER SERVICE(S) POSSESSING ORGANIC CAPABILITY.
T	A FEDERAL AVIATION ADMINISTRATION ACTIVITY IS PROVIDING DEPOT MAINTENANCE SUPPORT.
U	UNASSIGNED. MISMO REVIEW NOT COMPLETED. CURRENT DEPOT REPAIR ARRANGEMENTS REMAIN IN EFFECT.
V	AN ACTIVITY WITHIN THE NAVY IS PROVIDING DEPOT MAINTENANCE SUPPORT.
W	A NATIONAL WEATHER SERVICE ACTIVITY IS PROVIDING DEPOT MAINTENANCE SUPPORT.
X	ALL OTHER CONDITIONS.
    

Code	Definition
A	 
B	CONSUMABLE ITEMS THAT ARE UNIQUE TO A WEAPON SYSTEM WHICH HAVE BEEN INCLUDED IN A PERFORMANCE BASED LOGISTICS (PBL) OR CONTRACTOR LOGISTICS SUPPORT (CLS) CONTRACT.
C	 
D	ITEMS OF SUCH IMPORTANCE TO THE OPERATIONS READINESS OF OPERATING UNITS THAT THEY ARE SUBJECT TO CONTINUING CENTRALIZED INDIVIDUAL ITEM MANAGEMENT AND ASSET CONTROL THROUGHOUT ALL COMMAND AND SUPPORT ECHELONS.
E	CENTRALLY MANAGED RECOVERABLE ITEMS DESIGNATED AS REPARABLE FOR THE REASONS THAT REPAIR OF UNSERVICEABLE QUANTITIES OF THE ITEMS ARE CONSIDERED BY THE INVENTORY MANAGER IN SATISFYING REQUIREMENTS PRIOR TO OR IN CONJUNCTION WITH DETERMINING PROCUREMENT QUANTITIES.
F	ITEMS ASSIGNED TO A SINGLE AGENCY OTHER THAN THE COMMODITY ORIENTED INTEGRATED MANAGER FOR INTEGRATED MANAGEMENT OR CONTROL. (THESE INCLUDE ITEMS CONTROLLED BY THE ENERGY RESEARCH AND DEVELOPMENT ADMINISTRATION OR NATIONAL SECURITY AGENCY, OR ITEMS ASSIGNED TO THE ARMY TANK-AUTOMOTIVE COMMAND (TACOM) FOR INTEGRATED MANAGEMENT.)
G	PART II. IMC CODES ARE INVALID FOR SUBMITTAL. IF AN INVALID IMC CODES IS ALREADY RECORDED ON AN ITEM, MAINTENEANCE ACTIONS AFFECTING SEGMENT B DATA ELEMENTS WILL NOT REJECT FOR INVALID IMC CODES (PART II) DURING THE EDIT PROCESS.
H	 
J	ITEMS DETERMINED BY TECHNICAL DECISION DURING THE PROVISIONING CYCLE, DURING INTRODUCTION INTO LOGISTIC SYSTEMS, OR AT TIME OF ITEM MANAGEMENT CODING, TO BE HIGHLY SUBJECT TO EITHER: (A) DESIGN CHANGE OF THE ITEM ITSELF, OR (B) REPLACEMENT OF THE ITEM ITSELF THROUGH MODIFICATION OF THE APPLICABLE NEXT HIGHER ASSEMBLY. THESE ITEMS WILL BE REVIEWED FOR RECODING WHEN THE IM IS NOTIFIED THAT THE ITEM IS USED BY ANOTHER SERVICE/AGENCY, WHEN THE DESIGN BECOMES STABILIZED, OR THEN THE ITEM HAS BEEN IN OPERATIONAL USE FOR TWO YEARS. IN ALL CASES THESE SHALL BE REVIEWED BY THE IM FOR IMC CHANGE NO LONGER THAN 2 YEARS AFTER IMC J ASSIGNMENT.
L	ITEMS FABRICATED AT A MILITARY INDUSTRIAL ACTIVITY FOR LOCAL USE OR DIRECT ISSUE. THIS CATEGORY INCLUDES THOSE ITEMS DESIGNATED FOR LOCAL FABRICATION AT SERVICE INDUSTRIAL ACTIVITIES FOR LOCAL USE OR DIRECT ISSUE TO CUSTOMERS INCLUDING THE SECURITY ASSISTANCE PROGRAM (SAP).
M	PART II. IMC CODES ARE INVALID FOR SUBMITTAL. IF AN INVALID IMC CODE IS ALREADY RECORDED ON AN ITEM, MAINTENANCE ACTIONS AFFECTING SEGMENT B DATA ELEMENTS WILL NOT REJECT FOR INVALID IMC CODES (PART II) DURING THE EDIT PROCESS.
N	MODIFICATION/ALTERATION/CONVERSION SETS OR KITS INTENDED FOR ONE-TIME USE. THIS CATEGORY COVERS SITUATIONS IN WHICH SUCH MODIFICATION, ALTERATION, OR CONVERSION SETS OR KITS ARE PROCURED FOR ONE TIME USE, AND REPLENISHMENT OR REPLACEMENT IS NOT CONTEMPLATED. THIS CATEGORY APPLIES EVEN WHEN PROCUREMENT OCCURS ON A PHASED BASIS. SPECIFICALLY, IT RETAINS UNDER THE MANAGEMENT OF THE SERVICE/AGENCY THOSE SETS OR KITS WHICH REQUIREMENTS ARE PROPERLY DETERMINED ON A PROGRAM BASIS, SUCH AS THE NUMBER OF EQUIPMENT TO BE MODIFIED.
P	ITEMS WHICH ARE USED IN NUCLEAR POWER PLANTS OR ASSOCIATED SYSTEMS AND WHICH REQUIRE STRINGENT TECHNICAL OR QUALITY CONTROL.
Q	CONSUMABLE ITEMS WHICH HAVE BEEN APPROVED BY DUSD AS SPECIAL WAIVERS TO CONSOLIDATION OF IMM.
R	PART II. IMC CODES ARE INVALID FOR SUBMITTAL. IF AN INVALID IMC CODE IS ALREADY RECORDED ON AN ITEM, MAINTENANCE ACTIONS AFFECTING SEGMENT B DATA ELEMENTS WILL NOT REJECT FOR INVALID IMC CODES (PART II) DURING THE EDIT PROCESS.
S	 
T	INTERIM IMC USED TO INDICATE CONSUMABLE ITEM HAS BEEN REVIEWED AND WILL BE TRANSFERRED TO DLA FOR IMM MANAGEMENT.
V	STAND-ALONE CONSUMABLE ITEMS WHICH ARE NOT PROCURED AND WILL NOT BE TRANSFERRED TO DLA FOR MANAGEMENT.
W	ITEMS WHICH ARE USED ONLY BY SECURITY ASSISTANCE (SA) PROGRAM CUSTOMERS, I.E., FOREIGN COUNTRIES AND INTERNATIONAL ORGANIZATIONS. THESE ITEMS ARE OFTEN CALLED NONSTANDARD OR FMS UNIQUE.
X	PART II. IMC CODES ARE INVALID FOR SUBMITTAL. IF AN INVALID IMC CODE IS ALREADY RECORDED ON AN ITEM, MAINTENANCE ACTIONS AFFECTING SEGMENT B DATA ELEMENTS WILL NOT REJECT FOR INVALID IMC CODES (PART II) DURING THE EDIT PROCESS.
Y	PART II. IMC CODES ARE INVALID FOR SUBMITTAL. IF AN INVALID IMC CODE IS ALREADY RECORDED ON AN ITEM, MAINTENANCE ACTIONS AFFECTING SEGMENT B DATA ELEMENTS WILL NOT REJECT FOR INVALID IMC CODES (PART II) DURING THE EDIT PROCESS.
Z	RELINQUISHMENT OF SERVICE MANAGEMENT OF AN ITEM IN DESIGNATED COMMODITY- ORIENTED FEDERAL SUPPLY CLASSES TO THE IMM (FSC MANAGER) FOR MANAGEMENT.

Code	Definition
A	SERVICE/AGENCY-REGULATED (SERVICE/AGENCY USE ONLY.) ISSUE, TRANSFER, OR SHIPMENT IS CONTROLLED BY AUTHORITIES ABOVE THE ICP LEVEL TO ASSURE PROPER AND EQUITABLE DISTRIBUTION. 1. THE USE OR STOCKAGE OF THE ITEM REQUIRES RELEASE AUTHORITY BASED ON PRIOR OR CONCURRENT JUSTIFICATION. 2. REQUISITIONS WILL BE SUBMITTED IN ACCORDANCE WITH AGENCY/SERVICE REQUISITIONING PROCEDURES.
B	INVENTORY CONTROL POINT (ICP)-REGULATED (SERVICE/AGENCY USE ONLY.) ISSUE, TRANSFER, OR SHIPMENT IS CONTROLLED BY THE ICP. 1. THE USE OR STOCKAGE OF THE ITEM REQUIRES RELEASE AUTHORITY BASED ON PRIOR OR CONCURRENT JUSTIFICATION. 2. REQUISITIONS WILL BE SUBMITTED IN ACCORDANCE WITH AGENCY/SERVICE REQUISITIONING PROCEDURE.
C	SERVICE/AGENCY-MANAGED (SERVICE/AGENCY USE ONLY.) ISSUE, TRANSFER, OR SHIPMENT IS NOT SUBJECT TO SPECIALIZED CONTROLS OTHER THAN THOSE IMPOSED BY INDIVIDUAL SERVICES SUPPLY POLICY. 1. THE ITEM IS CENTRALLY MANAGED, STOCKED, AND ISSUED. 2. REQUISITIONS WILL BE SUBMITTED IN ACCORDANCE WITH SERVICE REQUISITIONING PROCEDURES.
D	DOD INTEGRATED MATERIEL-MANAGED, STOCKED, AND ISSUED ISSUE, TRANSFER, OR SHIPMENT IS NOT SUBJECT TO SPECIALIZED CONTROLS OTHER THAN THOSE IMPOSED BY THE INTEGRATED MATERIEL MANAGER/SERVICE SUPPLY POLICY. 1. THE ITEM IS CENTRALLY MANAGED, STOCKED, AND ISSUED. 2. REQUISITIONS MUST CONTAIN THE FUND CITATION REQUIRED TO ACQUIRE THE ITEM. REQUISITIONS WILL BE SUBMITTED IN ACCORDANCE WITH INTEGRATED MATERIEL MANAGER(IMM)/SERVICE REQUISITIONING PROCEDURES.
E	OTHER SERVICE-MANAGED, STOCKED, AND ISSUED (FOR SERVICE USE ONLY IF SECONDARY INVENTORY CONTROL ACTIVITY LEVEL OF AUTHORITY (SICA LOA) IS 8D AND NONCONSUMABLE ITEM MATERIAL SUPPORT CODE (NIMSC) IS 6.) ISSUE, TRANSFER, OR SHIPMENT IS NOT SUBJECT TO SPECIALIZED CONTROLS OTHER THAN THOSE IMPOSED BY THE SERVICE REQUISITIONING POLICY. 1. THE ITEM IS CENTRALLY MANAGED, STOCKED, AND ISSUED. 2. REQUISITIONS MAY REQUIRE A FUND CITATION AND WILL BE SUBMITTED IN ACCORDANCE WITH THE SERVICE REQUISITIONING PROCEDURES.
F	FABRICATE OR ASSEMBLE # (NON-STOCKED ITEMS) NATIONAL STOCK NUMBERED ITEMS FABRICATED OR ASSEMBLED FROM RAW MATERIALS AND FINISHED PRODUCTS AS THE NORMAL METHOD OF SUPPORT. PROCUREMENT AND STOCKAGE OF THE ITEMS ARE NOT JUSTIFIED BECAUSE OF LOW USAGE OR PECULIAR INSTALLATION FACTORS. DISTINCTIONS BETWEEN LOCAL OR CENTRALIZED FABRICATE/ASSEMBLE CAPABILITY ARE IDENTIFIED BY THE SOURCE OF SUPPLY MODIFIER IN THE SOURCE OF SUPPLY COLUMN OF THE SERVICE MANAGEMENT DATA LISTS.
G	GENERAL SERVICES ADMINISTRATION (GSA)/CIVIL AGENCY INTEGRATED MATERIEL MANAGED, STOCKED, AND ISSUED IDENTIFIES GSA/CIVIL AGENCY-MANAGED ITEMS AVAILABLE FROM GSA/CIVIL AGENCY SUPPLY DISTRIBUTION FACILITIES. REQUISITIONS AND FUND CITATIONS WILL BE SUBMITTED IN ACCORDANCE WITH GSA/CIVIL AGENCY/SERVICE REQUISITIONING PROCEDURES.
H	DIRECT DELIVERY UNDER A CENTRAL CONTRACT # (VENDOR STOCKED) ISSUE, TRANSFER, OR SHIPMENT IS NOT SUBJECT TO SPECIALIZED CONTROLS OTHER THAN THOSE IMPOSED BY IMM/SERVICE/AGENCY SUPPLY POLICY. 1. THE ITEM IS CENTRALLY MANAGED AND PROCURED. 2. NORMAL ISSUE IS BY DIRECT SHIPMENT FROM THE VENDOR TO THE USER AT THE ORDER OF THE ICP OR IMM. HOWEVER, ORDERS MAY BE SHIPPED FROM STOCK BY ICP OR IMM DISTRIBUTION FACILITIES WHEN THE VENDOR'S MINIMUM ORDER QUANTITY IS NOT MET, OR WHEN STOCKS ARE BEING DRAWN DOWN. 3. REQUISITIONS AND FUND CITATIONS WILL BE SUBMITTED IN ACCORDANCE WITH IMM/SERVICE/AGENCY REQUISITIONING PROCEDURES. 4. GENERALLY, DELIVERY WILL BE MADE WITHIN APPLICABLE SERVICE/AGENCY GUIDELINES ADDRESSING CUSTOMER REQUIRED TIMEFRAMES.
I	DIRECT ORDERING FROM A CENTRAL CONTRACT/SCHEDULE (NON-STOCKED ITEMS) ISSUE, TRANSFER, OR SHIPMENT IS NOT SUBJECT TO SPECIALIZED CONTROLS OTHER THAN THOSE IMPOSED BY IMM/SERVICE SUPPLY POLICY. THE ITEM IS COVERED BY A CENTRALLY ISSUED CONTRACTUAL DOCUMENT, OR BY ANY MULTIPLE-AWARD FEDERAL SUPPLY SCHEDULE, WHICH PERMITS USING ACTIVITIES TO PLACE ORDERS DIRECTLY ON VENDORS FOR DIRECT DELIVERY TO THE USER.
J	NOT STOCKED, CENTRALLY PROCURED # (NON-STOCKED ITEMS) IMM/SERVICE CENTRALLY MANAGED BUT NOT STOCKED ITEM. PROCUREMENT WILL BE INITIATED ONLY AFTER RECEIPT OF A REQUISITION.
K	CENTRALLY STOCKED FOR OVERSEAS ONLY MAIN MEANS OF SUPPLY IS LOCAL PURCHASE OR DIRECT ORDERING FROM A CENTRAL CONTRACT/SCHEDULE WHEN THE FEDERAL SUPPLY SCHEDULE NUMBER IS SHOWN IN THE CMD RECORD. ITEM IS STOCKED IN DOMESTIC SUPPLY SYSTEM FOR THOSE ACTIVITIES UNABLE TO PROCURE LOCALLY DUE TO NONAVAILABILITY OF PROCUREMENT SOURCES OR WHERE LOCAL PURCHASE IS PROHIBITED (E.G., ASPR; FLOW OF GOLD; OR BY INTERNAL SERVICE/AGENCY RESTRAINTS). REQUISITIONS WILL BE SUBMITTED BY OVERSEAS ACTIVITIES IN ACCORDANCE WITH SERVICE/AGENCY REQUISITIONING PROCEDURES. NOTE: CONTINENTAL U.S. (CONUS) ACTIVITIES WILL OBTAIN SUPPLY SUPPORT THROUGH LOCAL PROCUREMENT PROCEDURES.
L	LOCAL PURCHASE # (NON-STOCKED ITEMS) DEFENSE LOGISTICS AGENCY (DLA)/GSA/SERVICE/AGENCY-MANAGED ITEMS AUTHORIZED FOR LOCAL PURCHASE AS NORMAL MEANS OF SUPPORT AT BASE, POST, CAMP, OR STATION LEVEL. ITEM NOT STOCKED IN WHOLESALE DISTRIBUTION SYSTEM OF IMM/SERVICE/AGENCY ICP.
M	RESTRICTED REQUISITIONS-MAJOR OVERHAUL (SERVICE/AGENCY USE ONLY.) ITEMS (ASSEMBLIES AND/OR COMPONENT PARTS) WHICH FOR LACK OF SPECIALIZED TOOLS, TEST EQUIPMENT, ETC., CAN BE USED ONLY BY MAJOR OVERHAUL ACTIVITIES. BASE, POST, CAMP, OR STATION ACTIVITIES WILL NOT REQUISITION UNLESS AUTHORIZED TO PERFORM MAJOR OVERHAUL FUNCTION.
N	RESTRICTED REQUISITIONING-DISPOSAL (SERVICE/AGENCY USE ONLY.) DISCONTINUED ITEMS NO LONGER AUTHORIZED FOR ISSUE EXCEPT ON THE SPECIFIC APPROVAL OF THE SERVICE INVENTORY MANAGER. REQUISITIONS MAY BE SUBMITTED IN ACCORDANCE WITH SERVICE REQUISITIONING PROCEDURES IN INSTANCES WHERE VALID REQUIREMENTS EXIST AND REPLACING ITEM DATA HAS NOT BEEN FURNISHED.
O	PACKAGED FUELS (NON-STOCKED ITEMS) DLA-MANAGED AND SERVICE-REGULATED. 1. ITEM WILL BE CENTRALLY PROCURED IN ACCORDANCE WITH DOD 4140.25-M, PROCEDURES FOR THE MANAGEMENT OF PETROLEUM PRODUCTS, BUT NOT STOCKED BY IMM. LONG LEAD TIME REQUIRED. 2. REQUIREMENTS WILL BE SATISFIED BY DIRECT SHIPMENT TO THE USER EITHER FROM A VENDOR OR FROM SERVICE ASSETS AT THE ORDER OF ICP OR IMM. 3. REQUIREMENTS AND/OR REQUISITIONS WILL BE SUBMITTED IN ACCORDANCE WITH SERVICE PROCEDURES.
P	RESTRICTED REQUISITION - SECURITY ASSISTANCE PROGRAM (SAP) 1. INDICATES ITEM IS STOCKED OR ACQUIRED ONLY FOR SAP (REPLACES MILITARY ASSISTANCE PROGRAM (MAP)) REQUIREMENTS OR 2. INDICATES ITEM IS NONSTOCKED AND MATERIEL IS ORDERED FROM THE CONTRACTOR FOR SHIPMENT DIRECTLY TO THE FOREIGN GOVERNMENT 3. BASE, POST, CAMP, OR STATION WILL NOT REQUISITION.
Q	BULK PETROLEUM PRODUCTS DLA-MANAGED. 1. ITEM MAY BE EITHER CENTRALLY STOCKED OR AVAILABLE BY DIRECT DELIVERY UNDER A CENTRAL CONTRACT. 2. REQUIREMENTS WILL BE SUBMITTED BY MILITARY SERVICES IN ACCORDANCE WITH IMM PROCEDURES. 3. ITEM WILL BE SUPPLIED IN ACCORDANCE WITH DOD 4140.25-M.
R	RESTRICTED REQUISITION-GOVERNMENT FURNISHED MATERIAL (GFM) INDICATES ITEM IS CENTRALLY PROCURED AND STOCKED AS GFM IN CONNECTION WITH THE MANUFACTURE OF MILITARY ITEMS. BASE, POST, CAMP, OR STATION WILL NOT REQUISITION.
S	RESTRICTED REQUISITIONING-OTHER SERVICE FUNDED (SERVICE USE ONLY.) FOR SERVICE-MANAGED ITEMS WHEREBY THE ISSUE, TRANSFER, OR SHIPMENT IS SUBJECT TO SPECIALIZED CONTROLS OF THE FUNDING MILITARY SERVICE. 1. ITEM IS PROCURED BY A MILITARY SERVICE FOR THE FUNDING MILITARY SERVICE AND IS CENTRALLY MANAGED BY THE FUNDING SERVICE. 2. THE PROCURING MILITARY SERVICE HAS NO REQUIREMENT IN ITS LOGISTIC SYSTEM FOR THE ITEM.
T	CONDEMNED (NON-STOCKED ITEMS) ITEM IS NO LONGER AUTHORIZED FOR PROCUREMENT, ISSUE, USE, OR REQUISITIONING.
U	LEAD SERVICE-MANAGED AS A MINIMUM PROVIDES PROCUREMENT, DISPOSAL, AND SINGLE SUBMITTER FUNCTIONS. WHOLESALE LOGISTICS RESPONSIBILITIES WHICH ARE TO BE PERFORMED BY THE PRIMARY INVENTORY CONTROL ACTIVITY (PICA) IN SUPPORT OF THE SICA ARE DEFINED BY THE SICA NIMSC CODE (SEE TABLE 107).
V	TERMINAL ITEM. IDENTIFIES ITEMS IN STOCK, BUT FUTURE PROCUREMENT IS NOT AUTHORIZED. REQUISITIONS MAY CONTINUE TO BE SUBMITTED UNTIL STOCKS ARE EXHAUSTED. PREFERRED ITEM NATIONAL STOCK NUMBER IS NORMALLY PROVIDED BY APPLICATION OF THE PHRASE: WHEN EXHAUSTED USE (NSN). REQUISITIONS WILL BE SUBMITTED IN ACCORDANCE WITH IMM/SERVICE REQUISITIONING PROCEDURES AS APPLICABLE.
W	RESTRICTED REQUISITIONING-SPECIAL INSTRUCTIONS APPLY (NON-STOCKED ITEMS) INDICATES STOCK NUMBER HAS BEEN ASSIGNED TO A GENERIC ITEM FOR USE IN BID INVITATIONS, ALLOWANCE LISTS, ETC., AGAINST WHICH NO STOCKS ARE EVER RECORDED. REQUISITIONS WILL BE SUBMITTED ONLY IN ACCORDANCE WITH IMM/SERVICE REQUISITIONING PROCEDURES. (THIS CODE WILL BE USED, WHEN APPLICABLE, IN CONJUNCTION WITH PHRASE CODE S (STOCK AS NSN(S)). IT IS CONSIDERED APPLICABLE FOR USE WHEN A PROCUREMENT SOURCE(S) BECOMES AVAILABLE. THE PHRASE CODE S AND THE APPLICABLE `STOCK AS' NSN(S) WILL THEN BE APPLIED FOR USE IN STOCK, STORE, AND ISSUE ACTIONS.)
X	SEMIACTIVE ITEM-NO REPLACEMENT (NON-STOCKED ITEMS) A POTENTIALLY INACTIVE NSN WHICH MUST BE RETAINED IN THE SUPPLY SYSTEM AS AN ITEM OF SUPPLY BECAUSE (1) STOCKS OF THE ITEM ARE ON HAND OR IN USE BELOW THE WHOLESALE LEVEL AND (2) THE NSN IS CITED IN EQUIPMENT AUTHORIZATION DOCUMENTS TO & E, TA, TM, ETC., OR IN-USE ASSETS ARE BEING REPORTED. 1. ITEMS ARE AUTHORIZED FOR CENTRAL PROCUREMENT BUT NOT AUTHORIZED FOR STOCKAGE AT WHOLESALE LEVEL. 2. REQUISITIONS FOR IN-USE REPLACEMENT WILL BE AUTHORIZED IN ACCORDANCE WITH INDIVIDUAL MILITARY SERVICE DIRECTIVES. 3. REQUISTIONS MAY BE SUBMITTED AS REQUIREMENTS GENERATE. REPETITIVE DEMANDS MAY DICTATE AN AAC CHANGE TO PERMIT WHOLESALE STOCKAGE.
Y	TERMINAL ITEM # (NON-STOCKED ITEMS) FUTURE PROCUREMENT IS NOT AUTHORIZED. NO WHOLESALE STOCK IS AVAILABLE FOR ISSUE. 1. REQUISITIONS WILL NOT BE PROCESSED TO THE WHOLESALE MANAGER. 2. INTERNAL SERVICE/AGENCY REQUISITIONING MAY BE CONTINUED IN ACCORDANCE WITH THE SERVICE/AGENCY REQUISITIONING POLICIES.
Z	INSURANCE/NUMERIC STOCKAGE OBJECTIVE ITEM. ITEMS WHICH MAY BE REQUIRED OCCASIONALLY OR INTERMITTENTLY, AND PRUDENCE REQUIRES THAT A NOMINAL QUANTITY OF MATERIEL BE STOCKED DUE TO THE ESSENTIALITY OR THE LEAD TIME OF THE ITEM. 1. THE ITEM IS CENTRALLY MANAGED, STOCKED, AND ISSUED. 2. REQUISITIONS WILL BE SUBMITTED IN ACCORDANCE WITH IMM/SERVICE REQUISITIONING PROCEDURES.
    

Code	Definition
A	ACTIVE. COMPANY CURRENTLY IN OPERATION. APPLICABILITY CAGE/NCAGE.
C	RESTRAINT. USE THE CAGE CODE INDICATED. (DO NOT USE FOR CATALOGING PURPOSES.) APPLICABILITY CAGE/NCAGE.
E	DEBARRED. THE COMPANY/ENTITY SHOWN IS DEBARRED, SUSPENDED OR PROPOSED FOR DEBARMENT AS INDICATED ON THE GSA LIST OF PARTIES EXCLUDED FROM PROCUREMENT PROGRAMS. NOTE: AT THE TIME THE COMPANY/ENTITY'S ELIGIBILITY HAS BEEN REINSTATED, THE STATUS CODE WILL BE CHANGED TO "Y" TO INDICATE THAT THE CONTRACTOR IS NOW ACTIVE, HOWEVER, HAS NOT INDICATED THEIR INTEREST IN RESUMING CONTRACTING WITH THE FEDERAL GOVERNMENT. THE COMPANY/ENTITY SEEKING TO RESUME BUSINESS MUST NOTIFY THE CONTRACTING ACTIVITY AND DLIS OF THEIR NEW STATUS. (DO NOT USE FOR CATALOGING PURPOSES.) APPLICABILITY CAGE.
F	OBSOLETE. LOCATION OF COMPANY UNKNOWN. REFERENCE NUMBERS CURRENTLY RECORDED IN THE FEDERAL/NATO SUPPLY SYSTEM. APPLICABILITY CAGE/NCAGE.
H	OBSOLETE. COMPANY HAS BEEN DISCONTINUED AND/OR CAGE/NCAGE NO LONGER REQUIRED. REFERENCE NUMBERS CURRENTLY RECORDED IN THE FEDERAL/NATO SUPPLY SYSTEM. APPLICABILITY CAGE/NCAGE.
J	SPECIALIZED USE. ACTIVE SPECIALIZED USE RECORD. DENOTES THE ITEM OF PRODUCTION RECORDED IN THE FEDERAL/NATO SUPPLY SYSTEM IS DESIGNED TO CERTAIN INDUSTRY WIDE SPECIFICATION(S) STANDARD(S). APPLICABILITY CAGE/NCAGE.
K	SPECIALIZED USE. ACTIVE SPECIALIZED USE RECORD DENOTING THE ITEM IS PRODUCED OR MEETS GOVERNMENT DESIGNED SPECIFICATION/STANDARD. APPLICABILITY CAGE/NCAGE.
M	SPECIALIZED USE. ACTIVE SPECIALIZED USE RECORD. CAGE/NCAGE IS REFERENCED TO A SPECIAL NUMBERING SYSTEM DEVELOPED BY THE GOVERNMENT AND USED IN CONJUNCTION WITH THE IDENTIFICATION OF CATALOGING DATA IN THE FEDERAL/NATO SUPPLY SYSTEM. APPLICABILITY CAGE/NCAGE
N	CANCELLED. CANCELLED WITHOUT REPLACEMENT RECORD. COMPANY IS DEFUNCT AND/OR CAGE/NCAGE IS NO LONGER REQUIRED. NO REFERENCE NUMBERS RECORDED IN THE FEDERAL/NATO SUPPLY SYSTEM. APPLICABILITY CAGE/NCAGE.
P	CANCELLED. CANCELLED WITHOUT REPLACEMENT RECORD. LOCATION OF COMPANY IS UNKNOWN. NO REFERENCE NUMBERS RECORDED IN THE FEDERAL/NATO SUPPLY SYSTEM. APPLICABILITY CAGE/NCAGE.
R	CANCELLED. CANCELLED WITH REPLACEMENT RECORD. COMPANY DISCONTINUED AND/OR ACQUIRED/MERGED WITHIN SUCCESSOR. APPLICABILITY CAGE/NCAGE.
T	SPECIALIZED USE. ACTIVE SPECIALIZED USE RECORD. JOINT VENTURE. COMPANY IS A 50/50 PARTNERSHIP. APPLICABILITY CAGE.
U	RESTRAINT. ACTIVE RECORD WITH RESTRAINT. MANUFACTURER'S REPRESENTATIVE. CODE IS ASSIGNED TO AN ORGANIZATION THAT REPRESENTS OTHER VARIOUS COMPANIES FOR VARIOUS REASONS. THE COMPANY BEING REPRESENTED WILL USUALLY HAVE THEIR OWN SPECIFIC CAGE CODE ASSIGNED. (DO NOT USE FOR CATALOGING PURPOSES.). APPLICABILITY CAGE (TYPE F ONLY).
W	RESTRAINT. ACTIVE RECORD WITH RESTRAINT. CAGE CODE ASSIGNED TO AN INDIVIDUAL EMPLOYED BY A COMPANY WHERE THAT INDIVIDUAL PERFORMS CONTRACTED WORK USING COMPANY NAME SEPARATE FROM THE COMPANY LOCATION. ADDRESS ON THIS RECORD WILL BE DIFFERENT THAN THE ADDRESS OF THE COMPANY ITSELF. (DO NOT USE FOR CATALOGING PURPOSES.)
Y	ACTIVE SPECIALIZED USE RECORD. CAGE/NCAGE ASSIGNED TO AN ENTITY STILL ACTIVELY ENGAGED IN BUSINESS OPERATIONS: HOWEVER, THE ENTITY NO LONGER WISHES TO BE CONSIDERED FOR CONTRACTING OR SELLS ITS PRODUCTS ONLY THROUGH DISTRIBUTORS. (DO NOT USE FOR PROCUREMENT PURPOSES).

Code	Definition
1	SOURCE CONTROL REFERENCE. THE NUMBER ASSIGNED BY A DESIGN CONTROL MANUFACTURER OF AN END ITEM OF EQUIPMENT, INCLUDING A GOVERNMENT ACTIVITY, TO A DRAWING THAT RESTRICTS PROCUREMENT (1) TO THE SPECIFIED ITEM(S) DESCRIBED ON THE DRAWING AND (2) TO THE STATED SOURCE(S) OF SUPPLY DESIGNATED THEREON. THESE RESTRICTIONS ARE IMPOSED ON THE COGNIZANT DESIGN ACTIVITY TO ENSURE PROCUREMENT OF THE ONLY ITEM(S) KNOWN AS A RESULT OF TEST OR EVALUATION TO BE SATISFACTORY FOR THE STATED CRITICAL APPLICATION. INCLUDES ONLY THOSE DRAWINGS WHICH MEET THE DEFINITION FOR SOURCE CONTROL DRAWING IN MIL-STD-100. (APPLICABLE ONLY TO TYPE 1, 1B, 2, 4, AND 4B ITEM IDENTIFICATIONS.)
2	DEFINITIVE GOVERNMENT SPECIFICATION OR STANDARD DESIGNATOR REFERENCE. A PART NUMBER, STYLE NUMBER, OR TYPE DESIGNATOR INCLUDED IN OR DEVELOPED IN ACCORDANCE WITH A GOVERNMENT SPECIFICATION OR STANDARD WHICH HAS THE EFFECT OF FULLY IDENTIFYING AN ITEM OF SUPPLY. THIS CODE SHALL ALSO BE USED FOR A GOVERNMENT SPECIFICATION OR STANDARD WHICH, ALTHOUGH NOT INCLUDING PART NUMBERS, STYLE NUMBERS, OR TYPE DESIGNATORS, COVERS A SINGLE ITEM OF SUPPLY. THESE REFERENCE NUMBERS MAY BE CODED WITH REFERENCE NUMBER VARIATION CODE (RNVC) 1 IN ACCORDANCE WITH VOLUME 2, PARAGRAPH 2.9.2.N.(4). (NON-DEFINITIVE GOVERNMENT SPECIFICATIONS OR STANDARD DESIGNATOR REFERENCES SHALL BE CODED 4; VENDOR ITEM DRAWINGS AS DEFINED IN MIL-STD-100 SHALL BE CODED 7; PROFESSIONAL ASSOCIATION OR STANDARD DESIGNATOR REFERENCES SHALL BE CODED 3.)
3	DESIGN CONTROL REFERENCE. THE PRIMARY NUMBER USED TO IDENTIFY AN ITEM OF PRODUCTION OR A RANGE OF ITEMS OF PRODUCTION, BY THE MANUFACTURER (INDIVIDUAL, COMPANY, FIRM, CORPORATION, OR GOVERNMENT ACTIVITY) WHICH CONTROLS THE DESIGN, CHARACTERISTICS, AND PRODUCTION OF THE ITEM BY MEANS OF ITS ENGINEERING DRAWINGS, SPECIFICATIONS AND INSPECTION REQUIREMENTS. (WHEN USED TO IDENTIFY A REFERENCE NUMBER WHERE THE DESIGN CONTROL REFERENCE IS NO LONGER ACTIVE (ORIGINAL DESIGN ACTIVITY), THE REFERENCE NUMBER WILL BE CODED WITH REFERENCE NUMBER VARIATION CODE (RNVC)9).
4	NON-DEFINITIVE U.S. GOVERNMENT SPECIFICATION OR STANDARD REFERENCE. ANY GOVERNMENT SPECIFICATION OR STANDARD REFERENCE OTHER THAN THOSE INDICATED IN CODE 2 AS DEFINITIVE REFERENCES. THIS CODE SHALL BE USED FOR NON-DEFINITIVE GOVERNMENT SPECIFICATIONS AND STANDARD REFERENCES AND NON-DEFINITIVE PART NUMBERS, TYPE DESIGNATORS, AND STYLE NUMBERS INCLUDED THEREIN WHICH ARE CODED WITH RNVC 1. (INCLUDES THE SPECIFICATION NUMBER OF THOSE SPECIFICATIONS FOR WHICH TYPE DESIGNATION IS USED AS CODE 2. EXCLUDES PROFESSIONAL ASSOCIATION, INDUSTRIAL ASSOCIATION, OR MANUFACTURER'S SPECIFICATION OR STANDARD REFERENCE WHICH SHALL BE CODED 3, AND VENDOR ITEM DRAWING AS DEFINED IN MIL-STD-100 WHICH SHALL BE CODED 7.)
5	SECONDARY REFERENCE. ANY ADDITIONAL NUMBER, OTHER THAN A PRIMARY NUMBER (CODES 1, 2, 3, 4), INFORMATIVE REFERENCE (CODE 6) OR VENDOR ITEM DRAWING REFERENCE (CODE 7) ASSIGNED TO AN ITEM OF PRODUCTION OR SUPPLY BY A COMMERCIAL OR GOVERNMENT ORGANIZATION, WHICH REPRESENTS THE SAME ITEM OF PRODUCTION OR SUPPLY TO WHICH THE NATIONAL STOCK NUMBER (NSN) WAS ASSIGNED. THE REFERENCE NUMBER MAY HAVE HAD AN RNCC OF 1, 2, 3, 4, OR 7 BUT HAS SINCE BEEN REPLACED IN THE ITEM-OF-SUPPLY CONCEPT OF THE NSN BY ANOTHER PRIMARY NUMBER. INCLUDES ADDITIONAL NUMBERS ASSIGNED BY THE DESIGN CONTROL ORGANIZATION; SUPERSEDED OR DISCONTINUED REFERENCE NUMBERS WHICH MAY HAVE RESULTED FROM: A MANUFACTURER'S CHANGE IN NUMBERING SYSTEM; THE MANUFACTURER NO LONGER PRODUCES THE ITEM OR IS NO LONGER A TECHNICALLY APPROVED SOURCE; THE MANUFACTURER OR SUPPLIER FOR THAT NUMBER IS OUT OF BUSINESS. NOTE: AN RNCC 5 REFERENCE WITH A REFERENCE NUMBER VARIATION CODE (RNVC) OF 2 SHALL NOT BE ADDED TO AN NSN WITH A STANDARD MILITARY DRAWING (SMD) OR MILITARY SPECIFICATION CODED RNCC-RNVC 2-2 UNLESS THE REFERENCE IS REGISTERED ON THE QUALIFIED PRODUCTS LIST (QPL) FOR THE SMD OR MIL SPEC. (OBSOLETE, SUPERSEDED, CANCELLED, OR DISCONTINUED REFERENCE NUMBERS CODED RNCC 5 SHALL BE CODED REFERENCE NUMBER VARIATION CODE 9. ALL SECONDARY REFERENCE EXTRA LONG REFERENCE NUMBER (ELRNS), WHETHER CURRENT, (OBSOLETE, SUPERSEDED, CANCELLED, OR DISCONTINUED, SHALL BE CODED RNCC 5 AND RNVC 1.)
6	INFORMATION REFERENCE. NORTH ATLANTIC TREATY ORGANIZATION (NATO) STOCK NUMBERS (CAGE CODE INTE9), PRODUCTION EQUIPMENT CODES (CAGE CODE 99998), AND DOD AMMUNITION CODES (CAGE CODE 99999) WHICH MAY BE RELATED TO NSNS. (REFERENCE NUMBERS FOR THE CAGE CODES CITED ABOVE SHALL BE CODED RNVC 9.) WITHIN NATO, THE DEFINITION MEANS THE FOLLOWING: INFORMATION REFERENCE ANY RELATED TO THE NSN WHICH DOES NOT FALL INTO ANY OTHER CATEGORY.
7	VENDOR ITEM DRAWING REFERENCE (FORMERLY SPECIFICATION CONTROL REFERENCE). THE NUMBER ASSIGNED BY A DESIGN ACTIVITY TO A DRAWING THAT IS NOT ITEM IDENTIFYING, BUT WHICH DELINEATES EXISTING COMMERCIAL OR VENDOR DEVELOPED ITEMS MEETING ALL ENGINEERING AND TEST REQUIREMENTS SPECIFIED, WITHOUT IMPOSING ADDITIONAL TEST/ENGINEERING REQUIREMENTS NOT NORMALLY PROVIDED BY THE VENDOR(S). INCLUDES ONLY THOSE DRAWINGS WHICH MEET THE DEFINITION OF VENDOR ITEM DRAWING IN MIL-STD-100. VENDOR ITEM DRAWING REFERENCES ARE ADMINISTRATIVE CONTROL NUMBERS AND SHALL NOT BE USED AS PART IDENTIFICATION NUMBERS.
8	US/NATO-REPRODUCED ITEM IDENTIFICATION NUMBER. A NUMBER REPRESENTING A REPRODUCTION OF AN ITEM OF PRODUCTION BY A NATO COUNTRY (INCLUDING THE UNITED STATES) FOR WHICH AUTHORIZATION TO USE THE NATO/NATIONAL STOCK NUMBER HAS BEEN GRANTED BY THE ORIGINATING COUNTRY. THE REPRODUCED ITEM REPRESENTS THE SAME ITEM OF PRODUCTION AS THE ORIGINAL ITEM.
A	DESIGN CATEGORY PACKAGING AND RELATED LOGISTICS DATA REFERENCE NUMBER. THE NUMBER OF A DOCUMENT REPRESENTING PACKAGING AND RELATED LOGISTICS DATA REQUIREMENTS.
C	ADVISORY REFERENCE. A NUMBER ASSIGNED TO AN ITEM OF PRODUCTION OR SUPPLY NOT INCLUDED IN THE ITEM-OF-SUPPLY CONCEPT TO WHICH THE NSN HAS BEEN ASSIGNED (E.G., AN ITEM THAT MAY HAVE BEEN USED IN THE PREPRODUCTION EQUIPMENT DESIGN WHICH HAS SINCE BEEN REDESIGNED OR REPLACED). USE OF THIS RNCC IS RESTRICTED TO CONDITIONS WHERE CROSS-REFERENCE IS REQUIRED TO ESTABLISH IDENTIFICATION TO AN ITEM OF SUPPLY. ADDITIONALLY, THERE IS NO DIRECT RELATIONSHIP OF THE REFERENCE NUMBER TO THE NSN OTHER THAN A SERVICE/AGENCY INDIVIDUAL DECISION. (RNCCC SHALL BE USED ONLY IN CONJUNCTION WITH RNVC 1.)
D	DRAWING NUMBER REFERENCE. A NUMBER ASSIGNED BY A DESIGN ACTIVITY TO A DRAWING OR OTHER TECHNICAL DOCUMENTATION WHICH IDENTIFIES A DRAWING/DOCUMENT THAT IS RELATED TO AN ITEM OF SUPPLY OR PRODUCTION BUT DOES NOT QUALIFY FOR ASSIGNMENT OF CODES 1, 3, 5, 7, OR C. CODE D REFERENCE NUMBERS WILL NOT BE USED IN ITEM-OF-SUPPLY DETERMINATIONS.
E	REPLACED REFERENCE NUMBER. A MANUFACTURER'S PART NUMBER, GOVERNMENT SPECIFICATION/STANDARD OR OTHER DESIGN CONTROL REFERENCE NUMBER THAT IS SUPERSEDED, DISCONTINUED OR REPLACED RESULTING FROM A CANCEL-USE ACTION ON A NSN WHICH WAS RECORDED WITH ISC 3 OR E. THIS REFERENCE NUMBER IS AUTOMATICALLY MOVED AND THIS CODE IS AUTOMATICALLY ASSIGNED, DO NOT SUBMIT FOR CATALOGING PURPOSE.

Code	Definition
1	A DESIGN CONTROL REFERENCE OR OTHER REFERENCE NUMBER THAT DOES NOT IDENTIFY AN ITEM OF PRODUCTION WITHOUT THE USE OF ADDITIONAL INFORMATION, OR IS EITHER A SPECIFICATION, PART, TYPE OR SIMILAR REFERENCE NUMBER THAT DOES NOT IDENTIFY AN ITEM OF SUPPLY WITHOUT THE USE OF ADDITIONAL INFORMATION.
2	A DESIGN CONTROL REFERENCE OR OTHER REFERENCE NUMBER THAT IS AN ITEM-IDENTIFYING NUMBER FOR AN ITEM OF PRODUCTION, OR IS EITHER A SOURCE CONTROL REFERENCE, A SPECIFICATION OR A STANDARD PART, TYPE, OR SIMILAR REFERENCE NUMBER THAT IS AN ITEM-IDENTIFYING NUMBER FOR AN ITEM OF SUPPLY.
3	A VENDOR'S REFERENCE (PART) NUMBER ON A SOURCE CONTROL ITEM, AS DEFINED IN MIL-STD-100A, WHICH IS REPARABLE THROUGH THE REMOVAL, EXCHANGE, AND REINSTALLATION OF COMPONENT PARTS. THE RELATED SOURCE CONTROL DOCUMENT NUMBER WILL ALSO REFLECT THE CODE 3. THIS CODE IS LIMITED TO A TYPE 1B OR 4B ITEM IDENTIFICATION.
8	A NON-ITEM-IDENTIFYING REFERENCE NUMBER THAT IS ADDED TO A REPLACEMENT NSN AS A RESULT OF A CANCEL-USE ACTION ON A NSN RECORDED WITH ISC 3 OR E. IT IS USED TO IDENTIFY THE ORIGINAL ITEM OF SUPPLY/REPLACED ITEM. THIS REFERENCE NUMBER IS AUTOMATICALLY MOVED AND THIS CODE IS AUTOMATICALLY ASSIGNED, DO NOT SUBMIT FOR CATALOGING PURPOSES.
9	A REFERENCE NUMBER WHICH WAS THE DESIGN CONTROL REFERENCE FOR THE ITEM OF SUPPLY CONCEPT (ORIGINAL DESIGN ACTIVITY) THAT IS NOW INACTIVE CODED REFERENCE NUMBER CATEGORY CODE (RNCC) 3; A SPECIFICATION, STANDARD, OR OTHER REFERENCE NUMBER WHICH IS SUPERSEDED, CANCELLED, OBSOLETE OR DISCONTINUED AND IS CODED RNCC 5; A REFERENCE NUMBER FOR INFORMATION ONLY IS CODED RNCC 6; A DRAWING WHICH IS THE SINGLE CONTROLLING REFERENCE NUMBER (SCRN) CODED RNCC 2 OR 7; OR A DRAWING NUMBER REFERENCE CODED RNCC D.

Code	Definition
1	THE REFERENCE NUMBER IS REPRESENTED BY A DRAWING AND THE DRAWING WAS AVAILABLE TO THE RNAAC, WHO MAY OR MAY NOT BE THE SUBMITTING ACTIVITY, AT THE TIME OF SUBMISSION OF THE REFERENCE NUMBER. THE RNAAC WILL FURNISH THE DRAWING UPON REQUEST.
2	THE REFERENCE NUMBER IS REPRESENTED BY A DRAWING AND THE DRAWING WAS AVAILABLE TO THE RNAAC, WHO MAY OR MAY NOT BE THE SUBMITTING ACTIVITY, AT THE TIME OF SUBMISSION OF THE REFERENCE NUMBER; HOWEVER, THE RNAAC CANNOT FURNISH THE DRAWING.
3	THE REFERENCE NUMBER IS REPRESENTED BY TECHNICAL DOCUMENTATION OTHER THAN A DRAWING AND THE DOCUMENTATION WAS AVAILABLE TO THE RNAACC, WHO MAY OR MAY NOT BE THE SUBMITTING ACTIVITY, AT THE TIME OF SUBMISSION OF THE REFERENCE NUMBER. THE RNAAC WILL FURNISH THE TECHNICAL DOCUMENTATION UPON REQUEST.
4	THE REFERENCE NUMBER IS REPRESENTED BY TECHNICAL DOCUMENTATION OTHER THAN A DRAWING AND THE DOCUMENTATION WAS AVAILABLE TO THE RNAAC, WHO MAY ORMAY NOT BE THE SUBMITTING ACTIVITY, AT THE TIME OF SUBMISSION OF THE REFERENCE NUMBER; HOWEVER, THE RNAAC CANNOT FURNISH THE TECHNICAL DOCUMENTATION.
5	THE REFERENCE NUMBER IS REPRESENTED BY A DRAWING, BUT THE DRAWING WAS NOT AVAILABLE TO THE RNAAC, WHO MAY OR MAY NOT BE THE SUBMITTING ACTIVITY, AT THE TIME OF SUBMISSION OF THE REFERENCE NUMBER.
6	THE REFERENCE NUMBER IS REPRESENTED BY TECHNICAL DOCUMENTATION OTHER THAN A DRAWING BUT THE DOCUMENTATION WAS NOT AVAILABLE TO THE RNAAC, WHO MAY OR MAY NOT BE THE SUBMITTING ACTIVITY, AT THE TIME OF SUBMISSION OF THE REFERENCE NUMBER.
9	THE REFERENCE NUMBER IS OF THE TYPE FOR WHICH AN INDICATION OF DOCUMENT AVAILABILITY IS NOT REQUIRED.
A	THE REFERENCE NUMBER IS REPRESENTED BY AN ENGINEERING DRAWING AND THE DRAWING IS AVAILABLE FOR UNLIMITED USE. THE DRAWING WILL BE FURNISHED BY THE ACTIVITY IDENTIFIED BY THE RNAAC UPON REQUEST.
B	THE REFERENCE NUMBER IS REPRESENTED BY AN ENGINEERING DRAWING. THE DRAWING IS AVAILABLE FOR LIMITED USE UNDER THE TERMS OF THE RIGHTS-IN-DATA CLAUSE OF THE CONTRACT BY WHICH THE DATA WAS OBTAINED AND WILL BE FURNISHED BY THE ACTIVITY IDENTIFIED BY THE RNAAC UPON REQUEST. DESCRIPTIVE DATA BASED ON LIMITED RIGHTS INFORMATION WILL NOT BE RELEASED TO THE GENERAL PUBLIC THROUGH PUBLICATIONS OR OTHER MEDIA.
C	THE REFERENCE NUMBER IS REPRESENTED BY AN ENGINEERING DRAWING. THE DRAWING IS AVAILABLE FOR UNLIMITED USE BUT UNDER THE SECURITY MEASURES SPECIFIED FOR THE LEVEL OF SECURITY CLASSIFICATION ASSIGNED. THE DRAWING WILL BE FURNISHED ONLY TO QUALIFIED REQUESTERS BY THE ACTIVITY IDENTIFIED BY THE RNAAC.
D	THE REFERENCE NUMBER IS REPRESENTED BY AN ENGINEERING DRAWING. THE DRAWING IS AVAILABLE FOR LIMITED USE UNDER THE TERMS OF THE RIGHTS-IN-DATA CLAUSE OF THE CONTRACT BY WHICH THE DATA WAS OBTAINED, AND UNDER THE SECURITY MEASURES SPECIFIED FOR THE LEVEL OF SECURITY CLASSIFICATION ASSIGNED. THE DRAWING WILL BE FURNISHED ONLY TO QUALIFIED REQUESTERS BY THE ACTIVITY IDENTIFIED BY THE RNAAC. DESCRIPTIVE DATA BASED ON LIMITED RIGHTS INFORMATION WILL NOT BE RELEASED TO THE GENERAL PUBLIC THROUGH PUBLICATIONS OR OTHER MEDIA.
E	THE REFERENCE NUMBER IS REPRESENTED BY ENGINEERING DATA OTHER THAN AN ENGINEERING DRAWING. THE DATA IS AVAILABLE FOR UNLIMITED USE AND WILL BE FURNISHED BY THE ACTIVITY IDENTIFIED BY THE RNAAC UPON REQUEST.
F	THE REFERENCE NUMBER IS REPRESENTED BY ENGINEERING DATA OTHER THAN AN ENGINEERING DRAWING. THE DATA IS AVAILABLE FOR LIMITED USE UNDER THE TERMS OF THE RIGHTS-IN-DATA CLAUSE OF THE CONTRACT BY WHICH THE DATA WAS OBTAINED AND WILL BE FURNISHED BY THE ACTIVITY IDENTIFIED BY THE RNAAC UPON REQUEST. DESCRIPTIVE DATA BASED ON LIMITED RIGHTS INFORMATION WILL NOT BE RELEASED TO THE GENERAL PUBLIC THROUGH PUBLICATIONS OR OTHER MEDIA.
G	THE REFERENCE NUMBER IS REPRESENTED BY ENGINEERING DATA OTHER THAN AN ENGINEERING DRAWING. THE DATA IS AVAILABLE FOR UNLIMITED USE BUT UNDER THE SECURITY MEASURES SPECIFIED FOR THE LEVEL OF SECURITY CLASSIFICATION ASSIGNED. THE DATA WILL BE FURNISHED ONLY TO QUALIFIED REQUESTERS BY THE ACTIVITY IDENTIFIED BY THE RNAAC.
H	THE REFERENCE NUMBER IS REPRESENTED BY ENGINEERING DATA OTHER THAN AN ENGINEERING DRAWING. THE DATA IS AVAILABLE FOR LIMITED USE UNDER THE TERMS OF THE RIGHTS-IN-DATA CLAUSE OF THE CONTRACT BY WHICH THE DATA WAS OBTAINED, AND UNDER THE SECURITY MEASURES SPECIFIED FOR THE LEVEL OF SECURITY CLASSIFICATION ASSIGNED. THE DATA WILL BE FURNISHED ONLY TO QUALIFIED REQUESTERS BY THE ACTIVITY IDENTIFIED BY THE RNAAC. DESCRIPTIVE DATA BASED ON LIMITED RIGHTS INFORMATION WILL NOT BE RELEASED TO THE GENERAL PUBLIC THROUGH PUBLICATIONS OR OTHER MEDIA.
U	A REFERENCE NUMBER REPRESENTED BY A BAR CODE STRUCTURE IN ACCORDANCE WITH AN ORGANIZATION SUCH AS THE UNIVERSAL CODE COUNCIL (UCC) OR THE EUROPEON ARTICLE NUMBERING ASSOCIATION (EAN). THE TECHNICAL DOCUMENTATION MAY OR MAY NOT BE AVAILABLE TO THE RNAAC.
X	DAC NOT KNOWN. FOUND ON U.S. NSNS THAT WERE ASSIGNED BEFORE 1975. CANNOT BE USED FOR NEW ITEM ASSIGNMENT, OR ANY MAINTENANCE ACTION ON OLDER NSNS

Code	Definition
1	NUMBER IS FORMATTED AS CONFIGURED ON THE ORIGINATING DOCUMENT WITH THE EXCEPTION OF THE MODIFICATION REQUIRED IN VOLUME 2, CHAPTER 2.9. 
3	NUMBER FORMAT IS UNKNOWN. (CODED RNFC 3 BY THE DEFENSE LOGISTICS SERVICES CENTER UPON IMPLEMENTATION OF FLIS.)
4	NUMBER IS TOTALLY IN-THE-CLEAR (WITHOUT MODIFICATION) AS ORIGINALLY CONFIGURED BY THE MANUFACTURER, DESIGN CONTROL ACTIVITY, OR SUPPLIER. 
5	THE REFERENCE NUMBER RESULTS FROM A CHANGE OF THE PART NUMBER (PN) BY CONVERSION OF NON LATIN NATIONAL CHARACTERS TO LATIN CHARACTERS INCLUDED IN THE TABLE OF CHARACTER SUB SET FOR THE EXCHANGE OF NATO CODIFICATION DATA. THIS CONVERSION IS IN ACCORDANCE WITH THE NATIONAL CONVERSION TABLE SUCH AS IT IS DEFINED BY THE NCB OF THE COUNTRY WHERE THE MANUFACTURER/DISTRIBUTOR IS LOCATED; THIS CONVERSION METHOD USUALLY IS IN ACCORDANCE WITH THE ISO STANDARD (SEE ISO/TC46/SC2 "CONVERSION OF WRITTEN LANGUAGES")

Code	Definition
A	MANUFACTURER AND REFERENCE NUMBER ARE AUTHORIZED FOR PROCUREMENT. UNDER THIS REFERENCE NUMBER ITEMS CAN BE PROCURED ONLY FROM THE MANUFACTURER IDENTIFED BY THE NCAGE.(NOTE: THIS CODE MAY ONLY BE USED FOR REFERENCE NUMBERS ORIGINATING FROM MANUFACTURERS' STANDARDS OR CATALOGS OR FOR COPYRIGHTED DRAWING NUMBERS.
B	MANUFACTURER AND/OR REFERENCE NUMBER ARE NOT AUTHORIZED FOR PROCUREMENT. (NOTE: THIS CODE MAY BE USED FOR OBSOLETE OR INFORMATIVE REFERENCE NUMBERS ONLY.)
C	THE REFERENCE NUMBER ORIGINATES FROM A DESCRIPTIVE TECHNICAL DOCUMENT OF THE PRODUCT, WHICH MAY BE USED AS A PROCUREMENT DOCUMENT WITHOUT RESTRICTIONS. THE NCAGE SPECIFIED FOR THIS REFERENCE NUMBER IDENTIFIES THE ORIGINATING ORGANIZATION OR AGENCY OF THE DOCUMENT BUT NOT THE SUPPLY SOURCE OF THE ITEM. (NOTE: THIS CODE IS TO BE ALLOCATED TO REFERENCE NUMBERS ORIGINATING FROM GENERALLY AVAILABLE SPECIFICATIONS/STANDARDS OR TO DRAWING NUMBERS FOR WHICH THE GOVERNMENT HAS SEPARATE PROPERTY RIGHTS OR FOR WHICH THE AUTHOR DOES NOT CLAIM ANY PROPERTY RIGHTS.
D	PROCUREMENT AUTHORITY OF THE MANUFACTURER AND REFERENCE NUMBER HAVE NOT YET BEEN CHECKED. (NOTE: THIS CODE IS TO BE ALLOCATED TO REFERENCE NUMBERS STILL REQUIRING CHECKS ON PROCUREMENT AUTHORITY.)
E	THE REFERENCE NUMBER ORGINIATES FROM A DESCRIPTIVE TECHNICAL DOCUMENT OF THE PRODUCT, WHICH, OWING TO CONTRACTUAL AGREEMENTS, MAY ONLY BE USED WITH RESTRICTIONS AS A PROCUREMENT DOCUMENT. THE NCAGE SPECIFIED FOR THIS REFERENCE NUMBER IDENTIFIES A GOVERNMENT AGENCY AS ORIGINATOR OR HOLDER OF USER RIGHTS OF THE TECHNICAL DOCUMENT BUT NOT THE SUPPLY SOURCE OF THE ITEM. (NOTE: THIS CODE IS TO BE ALLOCATED TO REFERENCE NUMBERS RELATED TO A TECHNICAL DOCUMENT FOR WHICH THE PROCURING AGENCY HAS THE USER RIGHTS OWING TO CONTRACTUAL ARRANGEMENTS. THE USER RIGHTS AUTHORIZE THE PROCURING AGENCY TO USE THE TECHNICAL DOCUMENT FOR PROCUREMENT PURPOSES WITHIN THE FRAMEWORK OF THE USER RIGHTS CONTRACT.)
F	THE REFERENCE NUMBER DENOTES A TECHNICAL DOCUMENT FOR PRODUCT WHICH IS SUBJECT TO QUALIFICATION. ANY SUCH PRODUCT CAN ONLY BE PROCURED FROM QUALIFIED MANUFACTURERS. (NOTE: THIS CODE IS BEING RELATED TO REFERENCE NUMBERS OF ITEMS REQUIRING SAFETY OF QUALIFY CRITERIA, DETERMINED SUBJECT AUTHORIZATION. THE LATTER ALSO APPLIES TO RELATED SUPPLY SOURCES.)
G	MANUFACTURER AND REFERENCE NUMBER ARE NOT AUTHORIZED FOR PROCUREMENT. NOTE: THIS CODE IS ALLOCATED TO REFERENCE NUMBERS OF MANUFACTURERS WHICH USE OTHER ORGANIZATIONS TO MARKET/DISTRIBUTE THEIR PRODUCTS.
H	THE REFERENCE NUMBER ORIGINATES FROM A TECHNICAL DOCUMENT DESCRIBING THE PRODUCT; THIS DOCUMENT MAY, OWING TO SPECIAL CONDITIONS, ONLY BE USED AS A PROCUREMENT DOCUMENT FOR ONE MANUFACTURER. THE NCAGE GIVEN WITH THE REFERENCE NUMBER IDENTIFIES AN AGENCY AS PUBLISHER OR AS A USER OF THE TECHNICAL DOCUMENTATION, NOT, HOWEVER, THE SOURCE OF THE ITEM. (NOTE: THIS CODE IDENTIFIES REFERENCE NUMBER OF SPECIFICATION/TECHNICAL DATA PACKAGES CONSISTING MAINLY OF COPYRIGHTED TECHNICAL DATA, E.G., DRAWING, AND THEREFORE AUTHORIZED FOR PROCUREMENT FROM ONE MANUFACTURER ONLY.)

Code	Definition
1	TECHNICAL DATA ON THE POSSIBLE DUPLICATED FEDERAL ITEM IDENTIFICATION HAVE BEEN REVIEWED, AND THE ADDITIONAL ITEMS OF PRODUCTION (REFERENCE NUMBERS) ARE NOT ACCEPTABLE FOR THE ITEM OF SUPPLY.
2	THE ADDITIONAL ITEMS OF PRODUCTION ASSOCIATED WITH THE PROPOSAL HAVE BEEN REVIEWED AND ARE CORRECTLY PROPOSED AS PRIMARY NUMBERS TO IDENTIFY THE ITEMS OF SUPPLY. COLLABORATING ACTIVITES HAVE NOT AGREED TO THE ADDITIONAL ITEMS OF PRODUCTION.
3	THE ADDITIONAL ITEMS OF PRODUCTION ASSOCIATED WITH THE PROPOSAL HAVE BEEN REVIEWED AND ARE CORRECTLY PROPOSED AS PRIMARY NUMBERS TO IDENTIFY THE ITEMS OF SUPPLY. TIME DOES NOT PERMIT COLLABORATION OF THESE ADDITIONAL ITEMS OF PRODUCTION.
4	DATA ON THE ADDITIONAL ITEMS OF PRODUCTION IS NOT AVAILABLE AND ACCEPTABILITY OF THE ADDITIONAL ITEMS OF PRODUCTION CANNOT BE DETERMINED. 
5	MATCH OF REFERENCE NUMBERS(S) BY AN ASSOCIATED CODE IS NOT VALID FOR THIS REFERENCE. 
6	THE ITEM OF SUPPLY REPRESENTED BY THE POSSIBLE DUPLICATE NATIONAL STOCK NUMBER (NSN) IS NOT A TECHNICALLY ACCEPTABLE REPLACEMENT IN THE APPLICATOIN REQUIRING THE ITEM OF PRODUCTION IDENTIFIED BY THE SUBMITTED REFERENCE. (JUSTIFICATION CODE 6 SHALL BE USED ONLY FOR THOSE REFERENCE NUMBERS WHICH ARE CODED REFERENCE NUMBER CATEGORY CODE (RNCC) C AND REFERENCE NUMBER VARIATION CODE (RNVC) 1.)
7	THE REFERENCE NUMBER REPRESENTS AN OBSOLETE OR DISCONTINUED ITEM WHICH HAS "ROLLED BACK" INTO STOCK, AND IT WOULD NOT BE APPROPRIATE TO MIX STOCK WITH THE CURRENT ITEM. (JUSTIFICATION CODE 7 SHALL BE USED ONLY WHEN IT IS NOT NECESSARY TO ACQUIRE AN NSN FOR A CANCELLED, SUPERSEDED, OR OBSOLETE REFERENCE NUMBER WHICH MATCHES A REFERENCE NUMBER IN THE DEFENSE LOGISTICS SERVICES CENTER TOTAL RECORD CODED RNCC 5 AND RNVC 9.)
8	MATCH OF REFERENCE NUMBER IS NOT VALID DUE TO THE HAZARDOUS CHARACTERISTICS CODE. HCC MUST BE DIFFERENT ON MATCHED REFERENCE NUMBERS IN ORDER TO USE THIS CODE.

Code	Definition
A1	RADIOACTIVE, LICENSED 
A2	RADIOACTIVE, EXEMPT 
A3	RADIOACTIVE EXEMPT AUTHORIZED 
B1	ALKALI, CORR, INORGANIC 
B2	ALKALI, CORR, ORGANIC 
B3	ALKALI, LOW RISK 
C1	ACID, CORR, INORGANIC 
C2	ACID, CORR, ORGANIC 
C3	ACID, LOW RISK 
C4	ACID, CORR/OXID, INORGANIC 
C5	ACID, CORR/OXID, ORGANIC 
D1	OXIDIZER 
D2	OXIDIZER, POISON 
D3	OXIDIZER, CORR, ACIDIC 
D4	OXIDIZER, CORR, ALKALI 
E1	EXPLOSIVE, MILITARY 
E2	EXPLOSIVE, LOW RISK 
F1	FLAM DOT PG I, OSHA IA 
F2	FLAM DOT PG II, OSHA IB 
F3	FLAM DOT PG III, OSHA IC 
F4	FLAM DOT PG III, OSHA II 
F5	FLAM, POISON 
F6	FLAMMABLE, CORR, ACIDIC 
F7	FLAMMABLE, CORR, ALKALI 
F8	FLAM SOLID 
G1	GAS, POISON 
G2	GAS, FLAM 
G3	GAS, NON FLAM 
G4	GAS, NON FLAM, OXIDIZER 
G5	GAS, NON FLAM, CORROSIVE 
G6	GAS, POISON, CORROSIVE 
G7	GAS, POISON, OXIDIZER 
G8	GAS, POISON, FLAM 
G9	GAS, POISON, CORR, OXIDIZER 
H1	HAZ CHAR NOT DETERMINED 
K1	INFECTIOUS SUB 
K2	CYTOTOXIC DRUG 
M1	MAGNETIZED MATERIAL 
N1	NON HAZARDOUS 
P1	PEROXIDE ORGANIC, DOT 
P2	PEROXIDE ORGAN, LOW RISK 
R1	REACTIVE CHEM FLAMMABLE 
R2	WATER REACTIVE CHEMICAL 
T1	DOT POISON INHALE HAZARD 
T2	UN POISON, PG I 
T3	UN POISON, PG II 
T4	POISON FOOD CONTAMINANT 
T5	PESTICIDE LOW RISK 
T6	HEALTH HAZARD 
T7	CARCINOGEN 
V1	MISC HAZ MATL CLASS 9 
V2	AEROSOL, NONFLAMMABLE 
V3	AEROSOL, FLAMMABLE 
V4	COMBUSTIBLE LIQUID 
V5	HIGH FLASH LIQUID 
V6	PETROLEUM PRODUCTS 
V7	ENVIRONMENTAL HAZARD 
X1	MULTIPLE HAZARDS 
Z1	ARTICLE, ASBESTOS 
Z2	ARTICLE, MERCURY 
Z3	ARTICLE, PCB 
Z4	BATT, LEAD ACID, NONSPIL 
Z5	BATT, NICAD, NONSPIL 
Z6	BATTERY, LITHIUM 
Z7	BATTERY, DRY CELL 
    

Code	Definition
A	SERVICE/AGENCY-REGULATED (SERVICE/AGENCY USE ONLY.) ISSUE, TRANSFER, OR SHIPMENT IS CONTROLLED BY AUTHORITIES ABOVE THE ICP LEVEL TO ASSURE PROPER AND EQUITABLE DISTRIBUTION. 1. THE USE OR STOCKAGE OF THE ITEM REQUIRES RELEASE AUTHORITY BASED ON PRIOR OR CONCURRENT JUSTIFICATION. 2. REQUISITIONS WILL BE SUBMITTED IN ACCORDANCE WITH AGENCY/SERVICE REQUISITIONING PROCEDURES.
B	INVENTORY CONTROL POINT (ICP)-REGULATED (SERVICE/AGENCY USE ONLY.) ISSUE, TRANSFER, OR SHIPMENT IS CONTROLLED BY THE ICP. 1. THE USE OR STOCKAGE OF THE ITEM REQUIRES RELEASE AUTHORITY BASED ON PRIOR OR CONCURRENT JUSTIFICATION. 2. REQUISITIONS WILL BE SUBMITTED IN ACCORDANCE WITH AGENCY/SERVICE REQUISITIONING PROCEDURE.
C	SERVICE/AGENCY-MANAGED (SERVICE/AGENCY USE ONLY.) ISSUE, TRANSFER, OR SHIPMENT IS NOT SUBJECT TO SPECIALIZED CONTROLS OTHER THAN THOSE IMPOSED BY INDIVIDUAL SERVICES SUPPLY POLICY. 1. THE ITEM IS CENTRALLY MANAGED, STOCKED, AND ISSUED. 2. REQUISITIONS WILL BE SUBMITTED IN ACCORDANCE WITH SERVICE REQUISITIONING PROCEDURES.
D	DOD INTEGRATED MATERIEL-MANAGED, STOCKED, AND ISSUED ISSUE, TRANSFER, OR SHIPMENT IS NOT SUBJECT TO SPECIALIZED CONTROLS OTHER THAN THOSE IMPOSED BY THE INTEGRATED MATERIEL MANAGER/SERVICE SUPPLY POLICY. 1. THE ITEM IS CENTRALLY MANAGED, STOCKED, AND ISSUED. 2. REQUISITIONS MUST CONTAIN THE FUND CITATION REQUIRED TO ACQUIRE THE ITEM. REQUISITIONS WILL BE SUBMITTED IN ACCORDANCE WITH INTEGRATED MATERIEL MANAGER(IMM)/SERVICE REQUISITIONING PROCEDURES.
E	OTHER SERVICE-MANAGED, STOCKED, AND ISSUED (FOR SERVICE USE ONLY IF SECONDARY INVENTORY CONTROL ACTIVITY LEVEL OF AUTHORITY (SICA LOA) IS 8D AND NONCONSUMABLE ITEM MATERIAL SUPPORT CODE (NIMSC) IS 6.) ISSUE, TRANSFER, OR SHIPMENT IS NOT SUBJECT TO SPECIALIZED CONTROLS OTHER THAN THOSE IMPOSED BY THE SERVICE REQUISITIONING POLICY. 1. THE ITEM IS CENTRALLY MANAGED, STOCKED, AND ISSUED. 2. REQUISITIONS MAY REQUIRE A FUND CITATION AND WILL BE SUBMITTED IN ACCORDANCE WITH THE SERVICE REQUISITIONING PROCEDURES.
F	FABRICATE OR ASSEMBLE # (NON-STOCKED ITEMS) NATIONAL STOCK NUMBERED ITEMS FABRICATED OR ASSEMBLED FROM RAW MATERIALS AND FINISHED PRODUCTS AS THE NORMAL METHOD OF SUPPORT. PROCUREMENT AND STOCKAGE OF THE ITEMS ARE NOT JUSTIFIED BECAUSE OF LOW USAGE OR PECULIAR INSTALLATION FACTORS. DISTINCTIONS BETWEEN LOCAL OR CENTRALIZED FABRICATE/ASSEMBLE CAPABILITY ARE IDENTIFIED BY THE SOURCE OF SUPPLY MODIFIER IN THE SOURCE OF SUPPLY COLUMN OF THE SERVICE MANAGEMENT DATA LISTS.
G	GENERAL SERVICES ADMINISTRATION (GSA)/CIVIL AGENCY INTEGRATED MATERIEL MANAGED, STOCKED, AND ISSUED IDENTIFIES GSA/CIVIL AGENCY-MANAGED ITEMS AVAILABLE FROM GSA/CIVIL AGENCY SUPPLY DISTRIBUTION FACILITIES. REQUISITIONS AND FUND CITATIONS WILL BE SUBMITTED IN ACCORDANCE WITH GSA/CIVIL AGENCY/SERVICE REQUISITIONING PROCEDURES.
H	DIRECT DELIVERY UNDER A CENTRAL CONTRACT # (VENDOR STOCKED) ISSUE, TRANSFER, OR SHIPMENT IS NOT SUBJECT TO SPECIALIZED CONTROLS OTHER THAN THOSE IMPOSED BY IMM/SERVICE/AGENCY SUPPLY POLICY. 1. THE ITEM IS CENTRALLY MANAGED AND PROCURED. 2. NORMAL ISSUE IS BY DIRECT SHIPMENT FROM THE VENDOR TO THE USER AT THE ORDER OF THE ICP OR IMM. HOWEVER, ORDERS MAY BE SHIPPED FROM STOCK BY ICP OR IMM DISTRIBUTION FACILITIES WHEN THE VENDOR'S MINIMUM ORDER QUANTITY IS NOT MET, OR WHEN STOCKS ARE BEING DRAWN DOWN. 3. REQUISITIONS AND FUND CITATIONS WILL BE SUBMITTED IN ACCORDANCE WITH IMM/SERVICE/AGENCY REQUISITIONING PROCEDURES. 4. GENERALLY, DELIVERY WILL BE MADE WITHIN APPLICABLE SERVICE/AGENCY GUIDELINES ADDRESSING CUSTOMER REQUIRED TIMEFRAMES.
I	DIRECT ORDERING FROM A CENTRAL CONTRACT/SCHEDULE (NON-STOCKED ITEMS) ISSUE, TRANSFER, OR SHIPMENT IS NOT SUBJECT TO SPECIALIZED CONTROLS OTHER THAN THOSE IMPOSED BY IMM/SERVICE SUPPLY POLICY. THE ITEM IS COVERED BY A CENTRALLY ISSUED CONTRACTUAL DOCUMENT, OR BY ANY MULTIPLE-AWARD FEDERAL SUPPLY SCHEDULE, WHICH PERMITS USING ACTIVITIES TO PLACE ORDERS DIRECTLY ON VENDORS FOR DIRECT DELIVERY TO THE USER.
J	NOT STOCKED, CENTRALLY PROCURED # (NON-STOCKED ITEMS) IMM/SERVICE CENTRALLY MANAGED BUT NOT STOCKED ITEM. PROCUREMENT WILL BE INITIATED ONLY AFTER RECEIPT OF A REQUISITION.
K	CENTRALLY STOCKED FOR OVERSEAS ONLY MAIN MEANS OF SUPPLY IS LOCAL PURCHASE OR DIRECT ORDERING FROM A CENTRAL CONTRACT/SCHEDULE WHEN THE FEDERAL SUPPLY SCHEDULE NUMBER IS SHOWN IN THE CMD RECORD. ITEM IS STOCKED IN DOMESTIC SUPPLY SYSTEM FOR THOSE ACTIVITIES UNABLE TO PROCURE LOCALLY DUE TO NONAVAILABILITY OF PROCUREMENT SOURCES OR WHERE LOCAL PURCHASE IS PROHIBITED (E.G., ASPR; FLOW OF GOLD; OR BY INTERNAL SERVICE/AGENCY RESTRAINTS). REQUISITIONS WILL BE SUBMITTED BY OVERSEAS ACTIVITIES IN ACCORDANCE WITH SERVICE/AGENCY REQUISITIONING PROCEDURES. NOTE: CONTINENTAL U.S. (CONUS) ACTIVITIES WILL OBTAIN SUPPLY SUPPORT THROUGH LOCAL PROCUREMENT PROCEDURES.
L	LOCAL PURCHASE # (NON-STOCKED ITEMS) DEFENSE LOGISTICS AGENCY (DLA)/GSA/SERVICE/AGENCY-MANAGED ITEMS AUTHORIZED FOR LOCAL PURCHASE AS NORMAL MEANS OF SUPPORT AT BASE, POST, CAMP, OR STATION LEVEL. ITEM NOT STOCKED IN WHOLESALE DISTRIBUTION SYSTEM OF IMM/SERVICE/AGENCY ICP.
M	RESTRICTED REQUISITIONS-MAJOR OVERHAUL (SERVICE/AGENCY USE ONLY.) ITEMS (ASSEMBLIES AND/OR COMPONENT PARTS) WHICH FOR LACK OF SPECIALIZED TOOLS, TEST EQUIPMENT, ETC., CAN BE USED ONLY BY MAJOR OVERHAUL ACTIVITIES. BASE, POST, CAMP, OR STATION ACTIVITIES WILL NOT REQUISITION UNLESS AUTHORIZED TO PERFORM MAJOR OVERHAUL FUNCTION.
N	RESTRICTED REQUISITIONING-DISPOSAL (SERVICE/AGENCY USE ONLY.) DISCONTINUED ITEMS NO LONGER AUTHORIZED FOR ISSUE EXCEPT ON THE SPECIFIC APPROVAL OF THE SERVICE INVENTORY MANAGER. REQUISITIONS MAY BE SUBMITTED IN ACCORDANCE WITH SERVICE REQUISITIONING PROCEDURES IN INSTANCES WHERE VALID REQUIREMENTS EXIST AND REPLACING ITEM DATA HAS NOT BEEN FURNISHED.
O	PACKAGED FUELS (NON-STOCKED ITEMS) DLA-MANAGED AND SERVICE-REGULATED. 1. ITEM WILL BE CENTRALLY PROCURED IN ACCORDANCE WITH DOD 4140.25-M, PROCEDURES FOR THE MANAGEMENT OF PETROLEUM PRODUCTS, BUT NOT STOCKED BY IMM. LONG LEAD TIME REQUIRED. 2. REQUIREMENTS WILL BE SATISFIED BY DIRECT SHIPMENT TO THE USER EITHER FROM A VENDOR OR FROM SERVICE ASSETS AT THE ORDER OF ICP OR IMM. 3. REQUIREMENTS AND/OR REQUISITIONS WILL BE SUBMITTED IN ACCORDANCE WITH SERVICE PROCEDURES.
P	RESTRICTED REQUISITION - SECURITY ASSISTANCE PROGRAM (SAP) 1. INDICATES ITEM IS STOCKED OR ACQUIRED ONLY FOR SAP (REPLACES MILITARY ASSISTANCE PROGRAM (MAP)) REQUIREMENTS OR 2. INDICATES ITEM IS NONSTOCKED AND MATERIEL IS ORDERED FROM THE CONTRACTOR FOR SHIPMENT DIRECTLY TO THE FOREIGN GOVERNMENT 3. BASE, POST, CAMP, OR STATION WILL NOT REQUISITION.
Q	BULK PETROLEUM PRODUCTS DLA-MANAGED. 1. ITEM MAY BE EITHER CENTRALLY STOCKED OR AVAILABLE BY DIRECT DELIVERY UNDER A CENTRAL CONTRACT. 2. REQUIREMENTS WILL BE SUBMITTED BY MILITARY SERVICES IN ACCORDANCE WITH IMM PROCEDURES. 3. ITEM WILL BE SUPPLIED IN ACCORDANCE WITH DOD 4140.25-M.
R	RESTRICTED REQUISITION-GOVERNMENT FURNISHED MATERIAL (GFM) INDICATES ITEM IS CENTRALLY PROCURED AND STOCKED AS GFM IN CONNECTION WITH THE MANUFACTURE OF MILITARY ITEMS. BASE, POST, CAMP, OR STATION WILL NOT REQUISITION.
S	RESTRICTED REQUISITIONING-OTHER SERVICE FUNDED (SERVICE USE ONLY.) FOR SERVICE-MANAGED ITEMS WHEREBY THE ISSUE, TRANSFER, OR SHIPMENT IS SUBJECT TO SPECIALIZED CONTROLS OF THE FUNDING MILITARY SERVICE. 1. ITEM IS PROCURED BY A MILITARY SERVICE FOR THE FUNDING MILITARY SERVICE AND IS CENTRALLY MANAGED BY THE FUNDING SERVICE. 2. THE PROCURING MILITARY SERVICE HAS NO REQUIREMENT IN ITS LOGISTIC SYSTEM FOR THE ITEM.
T	CONDEMNED (NON-STOCKED ITEMS) ITEM IS NO LONGER AUTHORIZED FOR PROCUREMENT, ISSUE, USE, OR REQUISITIONING.
U	LEAD SERVICE-MANAGED AS A MINIMUM PROVIDES PROCUREMENT, DISPOSAL, AND SINGLE SUBMITTER FUNCTIONS. WHOLESALE LOGISTICS RESPONSIBILITIES WHICH ARE TO BE PERFORMED BY THE PRIMARY INVENTORY CONTROL ACTIVITY (PICA) IN SUPPORT OF THE SICA ARE DEFINED BY THE SICA NIMSC CODE (SEE TABLE 107).
V	TERMINAL ITEM. IDENTIFIES ITEMS IN STOCK, BUT FUTURE PROCUREMENT IS NOT AUTHORIZED. REQUISITIONS MAY CONTINUE TO BE SUBMITTED UNTIL STOCKS ARE EXHAUSTED. PREFERRED ITEM NATIONAL STOCK NUMBER IS NORMALLY PROVIDED BY APPLICATION OF THE PHRASE: WHEN EXHAUSTED USE (NSN). REQUISITIONS WILL BE SUBMITTED IN ACCORDANCE WITH IMM/SERVICE REQUISITIONING PROCEDURES AS APPLICABLE.
W	RESTRICTED REQUISITIONING-SPECIAL INSTRUCTIONS APPLY (NON-STOCKED ITEMS) INDICATES STOCK NUMBER HAS BEEN ASSIGNED TO A GENERIC ITEM FOR USE IN BID INVITATIONS, ALLOWANCE LISTS, ETC., AGAINST WHICH NO STOCKS ARE EVER RECORDED. REQUISITIONS WILL BE SUBMITTED ONLY IN ACCORDANCE WITH IMM/SERVICE REQUISITIONING PROCEDURES. (THIS CODE WILL BE USED, WHEN APPLICABLE, IN CONJUNCTION WITH PHRASE CODE S (STOCK AS NSN(S)). IT IS CONSIDERED APPLICABLE FOR USE WHEN A PROCUREMENT SOURCE(S) BECOMES AVAILABLE. THE PHRASE CODE S AND THE APPLICABLE `STOCK AS' NSN(S) WILL THEN BE APPLIED FOR USE IN STOCK, STORE, AND ISSUE ACTIONS.)
X	SEMIACTIVE ITEM-NO REPLACEMENT (NON-STOCKED ITEMS) A POTENTIALLY INACTIVE NSN WHICH MUST BE RETAINED IN THE SUPPLY SYSTEM AS AN ITEM OF SUPPLY BECAUSE (1) STOCKS OF THE ITEM ARE ON HAND OR IN USE BELOW THE WHOLESALE LEVEL AND (2) THE NSN IS CITED IN EQUIPMENT AUTHORIZATION DOCUMENTS TO & E, TA, TM, ETC., OR IN-USE ASSETS ARE BEING REPORTED. 1. ITEMS ARE AUTHORIZED FOR CENTRAL PROCUREMENT BUT NOT AUTHORIZED FOR STOCKAGE AT WHOLESALE LEVEL. 2. REQUISITIONS FOR IN-USE REPLACEMENT WILL BE AUTHORIZED IN ACCORDANCE WITH INDIVIDUAL MILITARY SERVICE DIRECTIVES. 3. REQUISTIONS MAY BE SUBMITTED AS REQUIREMENTS GENERATE. REPETITIVE DEMANDS MAY DICTATE AN AAC CHANGE TO PERMIT WHOLESALE STOCKAGE.
Y	TERMINAL ITEM # (NON-STOCKED ITEMS) FUTURE PROCUREMENT IS NOT AUTHORIZED. NO WHOLESALE STOCK IS AVAILABLE FOR ISSUE. 1. REQUISITIONS WILL NOT BE PROCESSED TO THE WHOLESALE MANAGER. 2. INTERNAL SERVICE/AGENCY REQUISITIONING MAY BE CONTINUED IN ACCORDANCE WITH THE SERVICE/AGENCY REQUISITIONING POLICIES.
Z	INSURANCE/NUMERIC STOCKAGE OBJECTIVE ITEM. ITEMS WHICH MAY BE REQUIRED OCCASIONALLY OR INTERMITTENTLY, AND PRUDENCE REQUIRES THAT A NOMINAL QUANTITY OF MATERIEL BE STOCKED DUE TO THE ESSENTIALITY OR THE LEAD TIME OF THE ITEM. 1. THE ITEM IS CENTRALLY MANAGED, STOCKED, AND ISSUED. 2. REQUISITIONS WILL BE SUBMITTED IN ACCORDANCE WITH IMM/SERVICE REQUISITIONING PROCEDURES.
    

Code	Definition
A12	U.S. ARMY SOLDIER'S BIOLOGICAL & CHEMICAL COMMAND, NATICK, MA 01760
A35	U.S. ARMY WAR RESERVE COMMAND, MATERIEL MANAGEMENT TEAM, NEW CUMBERLAND, PA 17070-5008
AKZ	US ARMY TANK-AUTOMOTIVE AND ARMAMENTS COMMAND WARREN, MI 48397-5000
AP5	U.S. ARMY SOLDIER'S BIOLOGICAL & CHEMICAL COMMAND, U.S. ARMY SUPPORT ACTIVITY, PHALIDELPHIA,PA 19101-3460
ARP	NAVICP-ERP 700 ROBBINS AVENUE PHILADELPHIA, PA 19111-5098
ARP	NAVICP-ERP 700 ROBBINS AVENUE PHILADELPHIA, PA 19111-5098
B14	U.S. ARMY ARMAMENT AND CHEMICAL ACQUISITION AND LOGISTICS ACTIVITY, ATTN: AMSTA-AC, ROCK ISLAND,IL 61299-6000
B16	US ARMY COMMUNICATIONS-ELECTRONICS COMMAND AND FORT MONMOUTH FORT MONMOUTH, NJ 07703-5016
B17	U.S. ARMY AVIATION & MISSILE COMMAND (AIR), ATTN: AMSMI-LC-MM-C, REDSTONE ARSENAL,AL 35898-5230
B56	US ARMY COMMUNICATIONS SECURITY LOGISTICS ACTIVITY FORT HUACHUCA, AZ 85613-7090
B63	USA BIOLOGICAL DEPOT, WASH, DC MAIL - COMMANDING GENERAL, WALTER REED ARMY MEDICAL CENTER, ATTN: CHIEF SUPPLY CONTROL BRANCH WASH, DC 20012
B64	U.S. ARMY AVIATION & MISSILE COMMAND, ATTN: AMSMI-LC-MM-C, REDSTONE ARSENAL,AL 35858-5230
B69	US ARMY MEDICAL MATERIEL AGENCY FREDERICK, MD 21701-5001
B69	US ARMY MEDICAL MATERIEL AGENCY FREDERICK, MD 21701-5001
BAM	SIMULATION, TRAINING AND INSTRUMENTATION COMMAND ORLANDO, FL 32826-3276
BAM	SIMULATION, TRAINING AND INSTRUMENTATION COMMAND ORLANDO, FL 32826-3276
BS7	TELEVISION-AUDIO SUPPORT ACTIVITY SACRAMENTO, CA 95813-5019
BS7	TELEVISION-AUDIO SUPPORT ACTIVITY SACRAMENTO, CA 95813-5019
CAT	CATERPILLAR INC, DEFENSE AND FEDERAL PRODUCTS DIV 14009 OLD GALENA ROAD, MOOSVILLE, IL 61552
CLC	THALES RAYTHEON SYSTEMS CO 2000 EAST EL SEGUNDO BLVD EL SEGUNDO, CA 90245-0902
CLC	THALES RAYTHEON SYSTEMS CO 2000 EAST EL SEGUNDO BLVD EL SEGUNDO, CA 90245-0902
F01	LOCKHEAD MARTIN AERONAUTICAL SYSTEMS, MARIETTA, GA 30063-0659
F04	AIR FORCE MEDICAL LOGISTICS OFFICE AFMLO/FOL FREDERICK, MD 21701-5006
F06	LOCKHEED MARTIN AERONAUTICAL SYSTEMS, KEESLER AFB, MS 39534-5249
F08	AEROSPACE INTEGRATION CORPORATION, 5555 JOHN GIVENS RD., CRESTVIEW, FL 32539-7019
F09	LOCKHEED MARTIN MISSION SYSTEMS, SANTA MARIA A 93455-1120
F13	PRATT & WHITNEY WEST PALM BEACH FL 33410-9600
F16	ROLLS ROYCE CORPORATION, 2840 FORTUNE CIRCLE WEST, INDIANAPOLIS IN 42641-5055
F20	L3 COMMUNICATION, INTEGRATED SYSTEMS, JOG, 91 HILL AVE, FORT WALTON BEACH FL 32548-7005
F27	WARNER ROBINS AIR LOGISTICS CENTER ROBINS AFB, GEORGIA 31098-5609
F28	THE BOEING COMPANY 626 ANCHORS ST. NW FORT WALTON BEACH, FL 32548-7013
F2U	WARNER-ROBINS AIR LOGISTICS CENTER ROBINS AFB, GEORGIA 31098-5609
F43	HONEYWELL TECHNICAL SERVICES, INC COLORADO SPRINGS, CO
F4U	OGDEN AIR LOGISTICS CENTER HILL AFB, UTAH 84056-5609
F50	THE BOEING COMPANY C-130 AVIONICS MOD PROGRAM
F52	ITT SENSOR
F56	FD9490 SOFSA EMB FOR DEPOT STORAGE ONLY 5749 BRIAR HILL RD LEXINGTON KY 40516-9721
F59	NORTHROP GRUMMAN IS ACS 2501 LIBERTY PARKWAY, SUITE 101 MIDWEST, OK 73110-2885
F63	COMPOSITE ENGINEERING, INC., 5281 RALEY BLVD., SACRAMENTO, CA. 95835-1701
F74	NORTHROP GRUMMAN CORPORATION WARNER ROBINS, GA 31088-7499
F77	BOEING MILITARY TRANSPORT AIRCRAFT, LONG BEACH CA 90807-3044
F78	NORTHROP GRUMMAN RYAN AERO SAN DIEGO CA 92127
F7X	AIR FORCE CRYPTOLOGIC SUPPORT CENTER (ESC) SAN ANTONIO, TEXAS 78243-5000
F80	WARNER ROBINS AIR LOGISTICS CENTER ROBINS AFB, GA 31098-5609
F81	LOCKHEED MARTIN AERO CO. 2211 NEW MARKET PKWY. S.E., SUITE 112 MARIETTA, GA 30067-9310
F83	GENERAL ATOMICS-AERONAUTICAL SYSTEMS, 16761 VIA DEL CAMPO COURT, SAN DIEGO, CA 92127-1713
F85	INTERNATIONAL TELEGRAPH & TELEPHONE 1030 S. HIGHWAY A1A, BLDG.989 PO BOX 245307, PATRICK AFB, FL 32925
F8U	TINKER AFB, OKLAHOMA 73145-5989
F92	AIR FORCE CLOTHING AND TEXTILE OFFICE PHILADELPHIA, PENNSYLVANIA 19101-8419
F97	HQ AIR FORCE ENGINEERING AND SERVICES CENTER/AFESC TYNDALL AFB, FLORIDA 32403-6001
FG5	OGDEN AIR LOGISTICS CENTER HILL AFB, UTAH 84056-5609
FGL	AF NUCLEAR WEAPONS PRODUCT SUPPORT CENTER KIRTLAND AFB, NM 87117-5617
FGZ	OGDEN AIR LOGISTICS CENTER HILL AFB, UTAH 84056-5609
FHZ	OKLAHOMA CITY AIR LOGISTICS CENTER TINKER AFB, OKLAHOMA 73145-5989
FL5	WARNER ROBINS AIR LOGISTICS CENTER ROBINS AFB, GEORGIA 31098-5609
FLZ	WARNER ROBINS AIR LOGISTICS CENTER ROBINS AFB , GEORGIA 31098-5609
FMS	AIR FORCE LOGISTICS COMMAND INTERNATIONAL LOGISTICS CENTER/MI WRIGHT PATTERSON AFB, OH 45433-5001
FND	AFMPC/MPCCM RANDOLPH AFB, TEXAS 78148
FNF	AFLC COMMAND CHAPLAIN HQ AFLC/HC WRIGHT-PATTERSON AFB, OHIO 45433-5001
FPD	AIR FORCE CRYPTOLOGIC SUPPORT CENTER (ESC) SAN ANTONIO, TEXAS 78243-5000
FPH	DETACHMENT 3, WR-ALC SAN ANTONIO, TEXAS 78241-5603
FPK	SAN ANTONIO AIR LOGISTICS CENTER KELLY AFB, TEXAS 78241-5000
FPZ	SAN ANTONIO AIR LOGISTICS CENTER KELLY AFB, TEXAS 78241-5000
FZZ	WR-ALC/LX, BLDG 350 STRM C, 750 3RD STREET, ROBINS AFB,GA, 31098-2122
G13	DEPARTMENT OF COMMERCE NATIONAL OCEANIC AND ATMOSPHERIC ADMINISTRATION NATIONAL WEATHER SERVICE - ENGINEERING DIVISION 1325 EAST-WEST HIGHWAY W/OSO322, SSMC2 SILVER SPRING MD 20910
G14	NATIONAL WEATHER SERVICE NATIONAL RECONDITIONING CENTER (NRC) 1520 E. BANNISTER ROAD KANSAS CITY, MO 64131
G36	VETERANS ADMINISTRATION SUPPLY DEPOT (901E) P.O. BOX 27 HINES, IL 60141
G69	DEPARTMENT OF TRANSPORTATION FEDERAL AVIATION ADMINISTRATION ATTN: AAC-490 P.O. BOX 25082 OKLAHOMA CITY, OK 73125
GF0	GENREAL SERVICES ADMINISTRATION GENERAL PRODUCTS COMMODITY CENTER FORT WORTH, TX 76102
GGE	GENREAL SERVICES ADMINISTRATION AUTOMATED DATA AND TELECOMMUNICATIONS SERVICES ELECTRONIC SERVICE DIVISION (WCE) 7TH & D STREETS, SW WASSHINGTON, D.C. 20407
GK0	GENREAL SERVICES ADMINISTRATION TOOLS MATERIAL MANAGEMENT DIVISION KANSAS CITY, MO 64131
GN0	GENREAL SERVICES ADMINISTRATION OFFICE OF SUPPLIES AND PAPER PRODUCTS COMMODITY CENTER NEW YORK, NY 10278
GQ0	GENREAL SERVICES ADMINISTRATION OFFICE AND SCIENTIFIC EQUIPMENT COMMODITY CENTER WASHINGTON, D.C. 20406
GSA	GENREAL SERVICES ADMINISTRATION WASHINGTON, D.C. 20406
GT0	GENREAL SERVICES ADMINISTRATION PRINTS AND CHEMICALS COMMODITY CENTER AUBURN, WASHINGTON 98002
GV0	GENREAL SERVICES ADMINISTRATION FURNITURE COMMODITY CENTER WASHINGTON, D.C. 20406
H9A	SPECIAL OPERATIONS FORCES SPT ACTY, BLDG 221 BLUE GRASS STATION, 5751 BRIAR HILL ROAD, LEXINGTON, KY 40512-4063
HAD	FIELD COMMAND, DEFENSE SPECIAL WEAPONS AGENCY KIRTLAND AFB, NEW MEXICO 87117-5669.
HAM	HQ USSOCOM/SOAL-LM 700 TAMPA POINT BLVD MACDILL AFB FL 33621-5323
HGD	HONEYWELL FEDERAL MANUFACTURING AND TECHNOLOGIES, KANSAS CITY, MO
HM8	DEFENSE SUPPLY CENTER RICHMOND (MAPPING) RICHMOND, VA 23297-5335
HQA	JOINT STRIKE FIGHTER PROGRAM OFFICE, CRYSTAL GATEWAY 4, 200 12TH ST STE 600, ARLINGTON, VA, 22203.
L01	COASTAL SYSTEMS STATION DAHLGREN DIVISION NAVAL SURFACE WARFARE CENTER PANAMA CITY, FL 32407-7001
L05	BAE SYSTEMS MARINE LTD, LANS BLDG C-08, BARROW-IN-FURNESS, CUMBRIA ENGLAND LA14 1AF
L46	ZODIAC OF NORTH AMERICA INC., ATTN: JACKIE DOLCH TEL. 410 -643-4141, 540 THOMPSON CREEK ROAD, STEVENSVILLE, MD 21666
LA1	FEDERAL PRISON INDUSTRIES FC1 ESTILL 100 PRISON RD ESTILL SC 29918-0699
LA2	TRACK INTERNATIONAL PRIME CONTRACTOR 369 W WESTERN AVE PORT WASHINGTON WI 53074-0990
LA3	TEREX CRANES INC CONWAY OPERATION PO BOX 260002 CONWAY SC 29528-6002
LA4	LITTON ELECTRO OPTICS SYSTEMS DIV ATTN US MARINE CORPS 12024 FORRESTGATE DRIVE DALLAS TX 75243-5411
LA5	HAYES DIVERSIFIED TECHNOLOGIES 10844 E AVE, SUITE A1 HESPERIA CA 92345-5000
LA6	ADVANCED VEHICLE SYSTEMS INC 600 NEW HAMPSHIRE AVE NW SUITE 1000 WASHINGTON DC 20037-2485
LA9	OSHKOSH TRUCK CORPORATION PO BOX 2566 2225 MINNESOTA ST OSHKOSH WI 54902-7021
LB2	LION-VALLEN INDUSTRIES 6450 POE AVE STE 300 DAYTON, OH 45414-2646
LB3	ISOMETRICS INC, 1266 N SCALES ST. PO BOX 660, ROCKINGHAM COUNTY, REIDSVILLE, NC 26320-8306
LB4	NAVISTAR INTERNATIONAL CORPORATION TRUCK OHIO PLAN, 6125 URBANA RD. PO BOX 600, SPRINGFIELD, OH 45501-0600
LB7	INGERSOLL RAND, MF M67854 01 L 3086, 501 SANDFORD AVE, MOCKSVILLE NC 27028-2919
LB8	ELGIN SWEEPER COMPANY SUBSIDIARY OF FEDERAL SIGNAL CORPS 1300 WEST BARTLETT ROAD ELGIN IL 60120-7429
LC1	XR RAYTHEON CO HANGER FACILITY BLDG 11005 BIGGS ARMY AIRFIELD EL PASO TX 79916-0001
LC2	INGERSOLL-RAND EQUIPMENT AND SERVICES CO 12311 WEST SILVER SPRING DRIVE MILWAUKEE, WI 53225
LC3	KALYN SIEBERT, 1505 WEST MAIN STREET, P.O. BOX 1078, GATESVILLE, TX 76528-6078
LC5	GENERAL DYNAMICS AMPHIBIOUS SYSTEMS FACILITY CODE 07LT9 14041 WORTH AVENUE WOODBRIDGE VA 22192-4123
LC6	RAYTHEON COMPANY PO BOX 801 MCKINNEY, TX 75070-0801
LC7	UNITED DEFENSE LP GROUND SYSTEM DIVISION P.O. BOX 15512 YORK, PA 17405-1512
LC8	CATERPILLAR INC DEFENSE FEDERAL PRODUCTS TC A 14009 OLD GALENDA RD MOSSVILLE, IL 61552-0470
LC9	AM GENERAL PO BOX 728 408 SOUTH BYRKIT ST MISHAWAKA, IN 46544-0728
LD2	AEROVIRONMENT, 69 MORELAND RD, SIMI VALLEY, CA 93065-1662
LD3	RO DEFENSE INC., 48 RAWLS SPRING LOOP RD, HATTIESBURG, MS 39402-7801
LD4	NORDIC AIR, INC. 5455 ROUTE 307 WEST GENEVA, OH 44041
LD6	HARRIS CORP GCSD, 2400 PALM BAY RD NE, PALM BAY FL 32905-3399
LD9	GYROCAM SYSTEMS LLC, 8100 15TH STREET EAST, SARASOTA, FL 34243
M00	RAYTHEON SYSTEMS COMPANY L00682, 2501 WEST UNIVERSITY DRIVE, P.O. BOX 801 M/S 8064, MCKINNEY TX 7570-0801
M01	TRAK INTERNATIONAL PRIME CONTRACTOR 369 W WESTERN AVE PORT WASHINGTON WI 53074-0990
M05	BAE SYSTEMS MARINE LTD, LANS BLDG M05C-08, BARROW-IN-FURNESS, CUMBRIA ENGLAND LA 141AF
M20	UNITED DEFENSE LP GROUND SYSTEMS DIV 1100 BAIRS RD, P.O. BOX 15512 YORK, PA 17405-1512
M31	CATERPILLAR INC, DEFENSE FEDERAL PRODUCTS TCA, 14009 OLD GALENA RD, MOSSVILLE, IL 61522-0407
M32	LION-VALLEN INDUSTRIES 6450 POE AVE STE 300 DAYTON, OH 45414-2646
MA6	ADVANCED VEHICLE SYSTEMS INC, L00864 600 NW HAMPSHIRE AVE, NW, STE 1000, WASHINGTON, DC 20037
MA7	HAYES DIVERSIFIED TECHNOLOGIES L00679, 10844 E AVE STE A1, HESPERIA, CA 92345
MA8	AM GENERAL L00211, P.O. BOX 728, 420 SOUTH BYRKIT ST. MISHAWAKA, IN 46522-3012
MA9	OSHKOSH TRUCK COMPANY, OSHKOSH, WI 54901
MHQ	HEADQUARTERS MARINE CORPS WASHINGTON, D.C. 20380
MPB	COMMANDING GENERAL MARINE CORPS LOGISTICS BASE G647-1, BLDG. 3700 ALBANY, GEORGIA 31704-5000
MTC	AMERICAN CRANE CORPORATION DBA TEREX AMERICAN INC 202 RALEIGH ST WILMINGTON, NC 28412-6363
N17	NAVY RESALE AND SERVICE SUPPORT OFFICE FORT WADSWORTH STATEN ISLAND, NY 10305
N21	NAVAL AIR SYSTEM COMMAND WASHINGTON, D.C. 20360
N22	NAVAL SUPPLY SYSTEMS COMMAND WASHINGTON, D.C. 20376
N23	NAVAL SEA SYSTEMS COMMAND WASHINGTON, D.C. 20362
N23	NAVAL SEA SYSTEMS COMMAND WASHINGTON, D.C. 20362
N24	PROGRAM EXECUTIVE OFFICER, EXPEDITIONARY WARFARE, ATTN: PMS 325J 2531 JEFFERSON DAVIS HIGHWAY, ARLINGTON, VA 22242-5171
N24	NAVAL SEA SYSTEMS COMMAND WASHINGTON, D.C. 20362
N25	NAVAL FACILITIES ENGINEERING COMMAND ALEXANDRIA, VIRGINIA 22332
N26	BUREAU OF NAVAL PERSONNEL WASHINGTON, D.C. 20370
N32	NAVAL INVENTORY CONTROL POINT PHILADELPHIA, PENNSYLVANIA 19111-5098
N35	NAVAL INVENTORY CONTROL POINT MECHANICSBURG, PENNSYLVANIA 17055-0788
N35	NAVAL INVENTORY CONTROL POINT MECHANICSBURG, PENNSYLVANIA 17055-0788
N35	NAVAL INVENTORY CONTROL POINT MECHANICSBURG, PENNSYLVANIA 17055-0788
N39	MILITARY SEALIFT COMMAND WASHINGTON, D.C. 20390
N43	NAVY FOOD SERVICE SYSTEMS OFFICE WASHINGTON NAVY YARD WASHINGTON, D.C. 20374
N44	STRATEGIC SYSTEMS PROJECT OFFICE WASHINGTON, D.C. 20376
N45	NAVAL TRAINING SYSTEM CENTER ORLANDO, FLORIDA 32813
N47	NAVY FLEET MATERIAL SUPPORT OFFICE MECHANICSBURG, PA 17055
N48	NAVAL EDUCATION AND TRAINING PROGRAM DEVELOPMENT CENTER PENSACOLA, FLORIDA 32509
N56	BUREAU OF MEDICINE AND SURGERY WASHINGTON, D.C. 20390
N57	CHIEF OF NAVAL OPERATIONS WASHINGTON, D.C. 20350
N64	COMMANDER NAVAL INTELLIGENCE COMMAND 4600 SILVER HILL ROAD WASHINGTON, D.C. 20389
N67	NAVAL AIR TECHNICAL SERVICES FACILITY PHILAEDELPHIA, PENNSYLVANIA 19111
N68	NAVAL UNDERWARTER SYSTEMS CENTER NEWPORT, RI 02840
N77	SPACE AND NAVAL WARFARE SYSTEMS COMMAND WASHINGTON, D.C. 20363
N79	NAVAL MINE ENGINEERING FACILITY YORKTOWN, VIRGINIA 23491
N84	NAVAL SHIP WEAPON SYSTEMS ENGINEERING STATION (CODE 5200) PORT HUENEME, CALIFORNIA 93041
NCB	NAVAL ORDNANCE CENTER P.O. BOX 2011 MECHANICSBURG, PENNSYLVANIA 17055-0788
NDZ	NAVAL SUPPLY CENTER SAN DIEGO, CALIFORNIA 92131
NFZ	NAVAL PUBLICATIONS AND FORMS DIRECTORATE NAVAL INVENTORY CONTROL POINT PHILADELPHIA, PENNSYLVANIA 19111-5098
NMP	NAVAL INVENTORY CONTREOL POINT P.O. BOX 2020 MECHANICSBURG, PA 17055-0788
NMZ	NAVAL INVENTORY CONTROL POINT P.O. BOX 2020 MECHANICSBURG, PA 17055-0788
NRP	NAVICP-ERP 700 ROBBINS AVENUE PHILADELPHIA, PA 19111-5098
NRP	NAVICP-ERP 700 ROBBINS AVENUE PHILADELPHIA, PA 19111-5098
NRP	NAVICP-ERP 700 ROBBINS AVENUE PHILADELPHIA, PA 19111-5098
NRP	NAVICP-ERP 700 ROBBINS AVENUE PHILADELPHIA, PA 19111-5098
NWS	NATIONAL WEATHER SERVICE 1325 EAST WEST HIGHWAY W/GOSO322 SILVER SPRING, MD 20910
P64	CRANE DIVISION NAVAL SURFACE WARFARE CENTER CODE 1121, BUILDING 41SE, 300 HIGHWAY 361 CRAVE, IN 47522-5010
P73	NAVAL UNDERSEA WARFARE ENGINEERING STATION SUPPLY DEPARTMENT KEYPORT, WA 98345
P87	NAVAL SURFACE WARFARE CENTER COASTAL SYSTEMS STATION 6703 W. HIGHWAY 98 CODE SP40, BUILDING 435 PANANA CITY, FL 32407-7001
PPZ	NAVAL AIR STATION SUPPLY DEPARTMENT PENSACOLA, FLORIDA 32508
PRZ	NAVAL AIR WAREFARE CENTER, AIRCRAFT DIVISION SUPPLY DEPARTMENT PATUXENT RIVER, MD 20670-5588
PSZ	PACIFIC MISSILE TEST CENTER POIT MUGU, CALIFORNIA 93042
Q1G	NAVAL ICP, PHILADELPHIA, PA 19111
Q1J	NAVAL ICP, PHILADELPHIA, PA 19111
Q6D	COMMUNICATIONS SECURITY MATERIAL SYSTEM 3801 NEBRASKA AVE N.W. WASHINGTON, D.C. 20390
Q81	JOINT CRUISE MISSILE PROJECT OFFICE WASHINGTON, D.C. 20360
R29	SSPO TECHNICAL REPRESENTATIVE (SSPOTR) SPERRY RAND CORP. SPERRY SYSTEMS MANAGEMENT DIVISION GREAT NECK, NEW YORK 11020
R31	NAVAL PLANT REPRESENTATIVE (SPL(W)) P.O. BOX 504 SUNNYVALE, CALIFORNIA 94088
R32	NAVAL SHIP ENGINEERING CENTER NAVAL STATION NORFOLK, VIRGINIA 23511
R33	NAVAL PLANT TECHNICAL REPRESENTATIVE (SPA) AUTONETICS DIVISION OF ROCKWELL INTERNATIONAL, INC. ANAHEIM, CALIFORNIA 92803
R41	COMMANDING OFFICER NAVAL CONSTRUCTION BATTALION CENTER CIVIL ENGINEER SUPPORT OFFICE CODE 15324 PORT HUENEME, CALIFORNIA 93043-5000
R48	NAVAL SUPPLY SYSTEMS COMMAND ARLINGTON, VA 22241-5360
R58	NAVY RECRUITING COMMAND ARLINGTON, VIRGINIA 22203
RAZ	NAVAL PLANT REPRESENTATIVE (SPL-60) LOCKHEED MISSILE AND SPACE CO. P.O. BOX 504 SUNNYVALE, CALIFORNIA 94088
RCZ	NAVAL PLANT REPRESENTATIVE (SPG) GENERAL ELECTRIC ORDNANCE SYSTEMS PITTSFIELD, MASSACHUSETTS 01201
RKZ	NAVAL PLANT TECHNICAL REPRESENTATIVE (SPI) INTERSTATE ELECTRONICS CORP. ANAHEIM, CALIFORNIA 92803
RTF	SPAWAR SYSCEN, CHARLESTON P.O. BOX 190022 NORTH CHARLESTON, SC 29419-9002
S9C	DEFENSE SUPPLY CENTER COLUMBUS, OHIO 43215
S9E	DEFENSE SUPPLY CENTER COLUMBUS, COLUMBUS, OH 43218
S9F	DEFENSE FUEL SUPPLY CENTER CAMERON STATION ALEXANDRIA, VA 22314
S9G	DEFENSE SUPPLY CENTER RICHMOND, VIRGINIA 23297
S9I	DEFENSE INDUSTRIAL SUPPLY CENTER PHILADELPHIA, PENNSYLVANIA 19111
S9M	DEFENSE SUPPLY CENTER PHILADELPHIA DIRECTORATE OF MEDICAL MATERIEL PHILADELPHIA, PENNSYLVANIA 19111
S9P	DEFENSE SUPPLY CENTER PHILADELPHIA PERISHABLE SUBSISTENCE PHILADELPHIA, PENNSYLVANIA 19101
S9R	DEFENSE SUPPLY CENTER RICHMOND, RICHMOND, VIRGINIA 23297
S9S	DEFENSE SUPPLY CENTER PHILADELPHIA NONPERISHABLE SUBSISTENCE PHILADELPHIA, PENNSYLVANIA 19101
S9T	DEFENSE SUPPLY CENTER PHILADELPHIA PHILADELPHIA, PENNSYLVANIA 19101
SMS	DEFENSE LOGISTICS AGENCY, ENTERPRISE BUSINESS SYSTEMS
ZIC	U.S. COAST GUARD SUPPLY CENTER CURTIS BAY BALTIMOIRE, MARYLAND 21226-1792
ZNC	COMMANDING OFFICER, USCG SURFACE FORCE LOGISTICS CENTER, CODE 028, MIL STOP 25, 2401 HAWKINS POINT ROAD, BALTIMORE, MARYLAND 21226-5000
ZQC	COMMANDING OFFICER, DEPARTMENT OF HOMELAND SECURITY, USCG AVIATION LOGISTICS CENTER, 1664 WEEKSVILLE ROAD, ELIZABETH CITY, NC 27909
    

Code	Definition
AM	A SMALL GLASS OR PLASTIC TUBE SEALED BY FUSION AFTER FILLING.
AT	A COLLECTION OF A VARIETY OF ITEMS THAT FALL INTO A CATEGORY OR CLASS PACKAGED AS A SMALL UNIT CONSTITUTING A SINGLE ITEM OF SUPPLY. USE ONLY WHEN THE TERM "ASSORTMENT" IS A PART OF THE ITEM NAME.
AY	A COLLECTION OF PARTS ASSEMBLED TO FORM A COMPLETE UNIT, CONSTITUTING A SINGLE ITEM OF SUPPLY, E.G., HOSE ASSEMBLY. USE ONLY WHEN THE TERM "ASSEMBLY" IS A PART OF THE ITEM NAME.
BA	A SPHERICAL-SHAPED MASS OF MATERIAL SUCH AS TWINE OR THREAD.
BD	A QUANTITY OF THE SAME ITEM TIED TOGETHER WITHOUT COMPRESSION.
BE	A SHAPED UNIT OF COMPRESSIBLE MATERIALS BOUND WITH CORD OR METAL TIES AND USUALLY WRAPPED, E.G., PAPER AND CLOTH RAGS.
BF	A UNIT OF MEASURE FOR LUMBER EQUAL TO THE VOLUME OF A BOARD 12" X 12" X 1".
BG	A FLEXIBLE CONTAINER OF VARIOUS SIZES AND SHAPES WHICH IS FABRICATED FROM SUCH MATERIALS AS PAPER, PLASTIC OR TEXTILES. INCLUDES `SACK' AND `POUCH'.
BK	A BOOK-LIKE PACKAGE, SUCH AS LABELS OR TICKETS, FASTENED TOGETHER ALONG ONE EDGE, USUALLY BETWEEN PROTECTIVE COVERS.
BL	A CYLINDRICAL CONTAINER, METAL OR WOOD, WITH SIDES THAT BULGE OUTWARD AND FLAT ENDS OR HEADS OF EQUAL DIAMETER. INCLUDES `KEG'.
BO	A FLAT FOLD OF FABRIC HAVING A STIFF PAPERBOARD CORE.
BR	A SOLID PIECE OR BLOCK OF VARIOUS MATERIALS, WITH ITS LENGTH GREATER THAN ITS OTHER DIMENSIONS, E.G., SOLDER. NOT APPLICABLE TO ITEMS SUCH AS SOAP, BEESWAX, BUFFING COMPOUND.
BT	A GLASS, PLASTIC, OR EARTHENWARE CONTAINER OF VARIOUS SIZES, SHAPES, AND FINISHES SUCH AS JUGS BUT EXCLUDING JARS, AMPOULES, VIALS, AND CARBOYS, WITH A CLOSURE FOR RETENTION OF CONTENTS.
BX	A RIGID, THREE DIMENSIONAL CONTAINER OF VARIOUS SIZES AND MATERIAL. INCLUDES "CASE", "CARTON", "TRAY", AND "CRATE".
CA	USUALLY A TUBULAR RECEPTACLE CONTAINING LOOSE OR PLIABLE MATERIAL AND DESIGNED TO PERMIT READY INSERTION INTO AN APPARATUS FOR DISPENSING THE MATERIAL. USUALLY ASSOCIATED WITH ADHESIVES AND SEALING COMPOUNDS.
CB	A HEAVY DUTY, BOTTLE-TYPE CONTAINER USED FOR TRANSPORTATION AND STORAGE OF LIQUIDS. USUALLY DESIGNED TO BE ENCASED IN A RIGID PROTECTIVE OUTER CONTAINER FOR SHIPMENT.
CD	A UNIT OF CUBIC MEASURE.
CE	A CONE-SHAPED MASS OF MATERIAL WOUND ON ITSELF SUCH AS TWINE OR THREAD, WOUND ON A CONICAL CORE.
CF	A UNIT OF CUBIC MEASURE.
CK	A BLOCK OF COMPACTED OR CONGEALED MATTER. APPLICABLE TO SUCH ITEMS AS SOAP, BUFFING COMPOUND.
CL	AN ARRANGEMENT OF MATERIAL SUCH AS WIRE, ROPE, AND TUBING WOUND IN A CIRCULAR SHAPE.
CM	A UNIT OF LINEAR MEASURE, EQUAL TO 1/100 OF A METER.
CN	A RIGID RECEPTACLE MADE OF FIBRE, METAL, PLASTIC, OR A COMBINATION THEREOF. CANS MAY BE CYLINDRICAL OR ANY NUMBER OF IRREGULAR SHAPES. RESTRICTED TO ITEMS WHICH CANNOT BE ISSUED IN LESS THAN CONTAINER QUANTITY. INCLUDES "PAIL" AND "CANISTER". DO NOT USE WHEN THE PACKAGED QUANTITY EQUATES TO A UNIT OF MEASURE, I.E., PINT, QUART, GALLON, OUNCE, OR POUND.
CO	A GENERAL TERM FOR USE ONLY WHEN AN ITEM IS PERMITTED TO BE PACKAGED FOR ISSUE IN OPTIONAL CONTAINERS, E.G., BOTTLE OR TUBE FOR A SINGLE NATIONAL STOCK NUMBER.
CY	A RIGID, CYLINDRICAL, METAL CONTAINER DESIGNED AS A PORTABLE CONTAINER FOR STORAGE AND TRANSPORTATION OF COMPRESSED GASSES, GENERALLY EQUIPPED WITH PROTECTED VALVE CLOSURE AND PRESSURE RELIEF SAFETY DEVICE.
CZ	A UNIT OF CUBIC MEASURE EXPRESSED IN THE METRIC SYSTEM OF MEASUREMENT. LIMITED IN APPLICATION TO LOCALLY ASSIGNED STOCK NUMBERS USED IN THE LOCAL PROCUREMENT OF ITEMS SUCH AS READY-MIX CONCRETE AND ASPHALT IN OVERSEA AREAS WHERE THE METRIC SYSTEM PREVAILS.
DR	A CYLINDRICAL CONTAINER DESIGNED AS AN EXTERIOR PACK FOR STORING AND SHIPPING BULK MATERIALS, E.G., FUELS, CHEMICALS, POWDERS, ETC. DRUMS MAY BE MADE OF METAL, RUBBER, POLYETHYLENE OR PLYWOOD, OR FIBRE WITH WOODEN, METAL, OR FIBRE ENDS.
DZ	TWELVE (12) OF AN ITEM OF SUPPLY.
EA	A NUMERIC QUANTITY OF ONE ITEM OF SUPPLY. DO NOT USE IF A MORE SPECIFIC TERM APPLIES, SUCH AS KIT, SET, ASSORTMENT, ASSEMBLY, GROUP, SHEET, PLATE, STRIP, OR LENGTH.
FT	UNIT OF LINEAR MEASUREMENT, SOMETIMES EXPRESSED AS `LINEAR FOOT'.
FV	FIVE (5) OF AN ITEM.
FY	FIFTY (50) OF AN ITEM.
GL	UNIT OF LIQUID MEASUREMENT.
GP	A COLLECTION OF RELATED ITEMS ISSUED AS A SINGLE ITEM OF SUPPLY, E.G., TEST SET GROUP. USE ONLY WHEN THE TERM `GROUP' IS A PART OF THE ITEM NAME.
GR	ONE HUNDRED FORTY-FOUR (144) OF AN ITEM.
HD	ONE HUNDRED (100) OF AN ITEM.
HK	A LOOP OF YARN OR ROPING, CONTAINING DEFINITE YARDAGE, E.G., COTTON, 840 YARDS; WORSTED, 560 YARDS. SEE `SKEIN' FOR COMPARISON.
IN	UNIT OF LINEAR MEASUREMENT, EQUIVALENT TO 1/12 OF A FOOT AND SOMETIMES EXPRESSED AS `LINEAR INCH'.
JR	A RIGID CONTAINER HAVING A WIDE MOUTH AND OFTEN NO NECK, TYPICALLY MADE OF EARTHENWARE OR GLASS. EXCLUDES `BOTTLE'.
KG	A UNIT OF MEASURE, EQUAL TO 1000 GRAMS.
KT	A COLLECTION OF RELATED ITEMS ISSUED AS A SINGLE ITEM OF SUPPLY, SUCH AS THE TOOLS, INSTRUMENTS, REPAIR PARTS, INSTRUCTION SHEETS AND OFTEN SUPPLIES TYPICALLY CARRIED IN A BOX OR BAG. ALSO INCLUDES SELECTED COLLECTIONS OF EQUIPMENT COMPONENTS, TOOLS, AND/OR MATERIALS FOR THE REPAIR, OVERHAUL, OR MODIFICATION OF EQUIPMENT. USE ONLY WHEN THE TERM "KIT" IS A PART OF THE ITEM NAME.
LB	A UNIT OF AVOIRDUPOIS WEIGHT MEASURE EQUIVALENT TO 16 OUNCES.
LG	TERM APPLIES TO ITEMS ISSUED IN FIXED OR SPECIFIC LINEAR MEASUREMENT, WITHOUT DEVIATION. THIS TERM NO LONGER APPLIES TO RANDOM LENGTHS WHICH WILL BE EXPRESSED IN DEFINITIVE UNITS OF LINEAR MEASURE SUCH AS FOOT OR YARD. EXCLUDES "STRIP".
LI	A UNIT OF LIQUID MEASURE EXPRESSED IN THE METRIC SYSTEM OF MEASUREMENT.
LT	A COLLECTION OF ASSOCIATED OR MISCELLANEOUS ARTICLES SOLD AS ONE UNIT
MC	A UNIT OF CUBIC MEASURE EXPRESSED IN ONE THOUSAND (1,000) INCREMENTS.
ME	THE MEASURE OF FOOD GENERALLY TAKEN BY AN INDIVIDUAL AT ONE TIME.
MM	A UNIT OF LINEAR MEASURE, EQUAL TO 1/1000 OF A METER.
MR	A UNIT OF LINEAR MEASURE EXPRESSED IN THE METRIC SYSTEM OF MEASUREMENT, EQUIVALENT TO 39.37 INCHES.
MX	ONE THOUSAND (1,000) OF AN ITEM.
OT	A COLLECTION OF RELATED ITEMS ISSUED AS A SINGLE ITEM OF SUPPLY, SUCH AS THE TOOLS, INSTRUMENTS, MATERIALS, EQUIPMENT, AND/OR INSTRUCTION MANUAL(S) FOR THE PRACTICE OF A TRADE OR PROFESSION OR FOR THE CARRYING OUT OF A PARTICULAR PROJECT OR FUNCTION. USE ONLY WHEN THE TERM "OUTFIT" IS A PART OF THE ITEM NAME.
OZ	A UNIT OF LIQUID OR AVOIRDUPOIS WEIGHT.
PD	MULTIPLE SHEETS OF PAPER THAT ARE STACKED TOGETHER AND FASTENED AT ONE END BY SEALING.
PG	A FORM OF PROTECTIVE WRAPPING FOR TWO OR MORE OF THE SAME ITEM OF SUPPLY. TO BE USED ONLY WHEN A UNIT OF MEASURE OR CONTAINER TYPE TERM IS NOT APPLICABLE. INCLUDES ``ENVELOPE'.
PM	A FLAT PIECE OF SQUARE OR RECTANGULAR-SHAPED METAL OF UNIFORM THICKNESS, USUALLY 1/4 INCH OR MORE. USE ONLY WHEN 'PLATE' (FEDERAL SUPPLY CLASSES (FSCS) 9515 AND 9535) IS USED IN AN ITEM NAME TO DENOTE SHAPE.
PR	TWO SIMILAR CORRESPONDING ITEMS, E.G., GLOVES, SHOES, BEARINGS; OR ITEMS INTEGRALLY FABRICATED OF TWO CORRESPONDING PARTS, E.G., TROUSER, SHEARS, GOGGLES.
PT	A UNIT OF LIQUID OR DRY MEASURE.
PZ	A CONTAINER USED FOR SUBSISTENCE ITEMS. USE ONLY WHEN `FOOD PACKET' IS PART OF THE ITEM NAME (FEDERAL SUPPLY GROUP (FSG) 89).
QT	A UNIT OF LIQUID OR DRY MEASURE.
RA	THE FOOD ALLOWANCE OF ONE PERSON FOR ONE DAY. USE ONLY WHEN ``RATION' (FSC 8970) IS A PART OF THE ITEM NAME.
RL	A CYLINDRICAL CORE ON WHICH A FLEXIBLE MATERIAL, SUCH AS WIRE OR CABLE, IS WOUND. USUALLY HAS FLANGED ENDS.
RM	A QUANTITY OF PAPER VARYING FROM 480 TO 516 SHEETS, DEPENDING UPON GRADE.
RO	A CYLINDRICAL CONFIGURATION OF FLEXIBLE MATERIAL WHICH HAS BEEN ROLLED ON ITSELF SUCH AS TEXTILES, TAPE, ABRASIVE PAPER, PHOTOSENSITIVE PAPER AND FILM, AND MAY UTILIZE A CORE WITH OR WITHOUT FLANGES.
SD	A PALLET-LIKE PLATFORM CONSISTING OF A LOAD-BEARING AREA FASTENED TO AND RESTING ON RUNNER TYPE SUPPORTS.
SE	A COLLECTION OF MATCHED OR RELATED ITEMS ISSUED AS A SINGLE ITEM OF SUPPLY, I.E., TOOL SETS, INSTRUMENT SETS, AND MATCHED SETS. USE ONLY WHEN THE TERM `SET' IS A PART OF THE ITEM NAME.
SF	A UNIT OF SQUARE MEASURE (AREA).
SH	A FLAT PIECE OF RECTANGULAR-SHAPED MATERIAL OF UNIFORM THICKNESS THAT IS VERY THIN IN RELATION TO ITS LENGTH AND WIDTH, SUCH AS METAL, PLASTIC, PAPER, AND PLYWOOD. USE OF THIS TERM IS NOT LIMITED TO ANY GROUP OF ITEMS OR FSCS. HOWEVER, IT WILL ALWAYS BE APPLIED WHEN "SHEET" IS USED IN THE ITEM NAME TO DENOTE SHAPE, E.G., ALUMINUM ALLOY SHEET, EXCEPT ITEMS IN FSC 7210.
SK	A LOOP OF YARN 120 YARDS IN LENGTH, USUALLY WOUND ON A 54-INCH CIRCULAR CORE. SEE `HANK' FOR COMPARISON.
SL	A CYLINDRICAL FORM WITH AN EDGE OR RIM AT EACH END AND AN AXIAL HOLE FOR A PIN OR SPINDLE ON WHICH A FLEXIBLE MATERIAL SUCH AS THREAD OR WIRE IS WOUND.
SO	A UNIT OF LINEAR MEASUREMENT, USUALLY APPLIED TO ANCHOR CHAIN; EQUIVALENT TO 15 FATHOMS (90 FT).
SP	A RELATIVELY NARROW, FLAT LENGTH OF MATERIAL, UNIFORM IN WIDTH, SUCH AS PAPER, WOOD, AND METAL. USE ONLY WHEN THE TERM "STRIP" IS A PART OF THE ITEM NAME.
SV	THE PURCHASE OF EMPLOYMENT, OR DEFINING OF WORK TO BE DONE
SX	MATERIAL IN A RELATIVELY LONG AND SLENDER, OFTEN CYLINDRICAL FORM FOR EASE OF APPLICATION OR USE, E.G., ABRASIVES.
SY	A UNIT OF SQUARE MEASURE (AREA).
TD	TWENTY-FOUR (24) OF AN ITEM.
TE	TEN (10) OF AN ITEM.
TF	TWENTY-FIVE (25) OF AN ITEM.
TN	THE EQUIVALENT OF 2000 LBS. INCLUDES SHORT TON AND NET TON.
TO	A UNIT OF TROY WEIGHT MEASURE, BASED ON 12 OUNCE POUND, GENERALLY APPLIED TO WEIGHTS OF PRECIOUS METALS.
TS	THIRTY-SIX (36) OF AN ITEM.
TU	NORMALLY A SQUEEZE-TYPE CONTAINER, MOST COMMONLY MANUFACTURED FROM A FLEXIBLE TYPE MATERIAL AND USED IN PACKAGING TOOTHPASTE, SHAVING CREAM, AND PHARMACEUTICAL PRODUCTS. ALSO APPLICABLE AS FORM AROUND WHICH ITEMS ARE WOUND, SUCH AS THREAD. IT IS NOT APPLICABLE TO MAILING TUBE, PNUEMATIC TUBE, OR CYLINDRICAL CONTAINERS OF A SIMILAR TYPE.
VI	A SMALL CONTAINER WHICH IS CYLINDRICAL IN SHAPE AND FLAT BOTTOMED WITH A VARIETY OF NECK FINISHES TO ACCOMMODATE ANY TYPE OF CAP, CORK, OR STOPPER.
YD	A UNIT OF LINEAR MEASURE, EQUIVALENT TO 3 FEET AND SOMETIMES EXPRESSED AS "LINEAR YARD".
    

Code	Definition
0	NO QUP
1	1
2	2
3	3
4	4
5	5
6	6
7	7
8	8
9	9
A	10
B	12
C	15
D	16
E	18
F	20
G	24
H	25
J	32
K	36
L	48
M	50
N	72
P	75
Q	100
R	120
S	144
T	200
U	250
V	500
W	1000
X	# BLK
Y	# PACKAGER OPTIONS SO LONG AS ALL OTHER CONTRACTUAL REQUIREMENTS ARE MET.
Z	* SPECIAL REQUIREMENTS.
    

Code	Definition
$	THIS CODE IDENTIFIES NUCLEAR WEAPONS USE CONTROL (UC) GROUND EQUIPMENT WHICH IS CIIC UNCLASSIFIED BUT MAY REQUIRE SPECIAL CONTROLS. USE CONTROL GROUND EQUIPMENT IS DESCRIBED AS RECODERS, VERIFIERS, ADAPTERS, POWER SUPPLIES, CABLES, PROGRAMMERS, MONITORS, CONTROLLERS, CODE PROCESSORS, POWER CONVERTERS, COMPUTERS AND DATA MODULES WHICH PERFORM A NUCLEAR WEAPON USE CONTROL FUNCTION. (SEE NOTE (2) BELOW).
1	HIGHEST SENSITIVITY (SRC-I) - UNCLASSIFIED AA&E. NON-NUCLEAR MISSILES,RECOILLESS RIFLES AND ROCKETS IN A READY-TO-FIRE (CERTIFIED ROUND) CONFIGURATION. EXAMPLES: (E.G., PATRIOT MISSILE LAUNCH CANNISTER, FIM-92 STINGER, M47 DRAGON, JAVELIN, M72 LAW, M136 AT4 LAAW, M141 BDM) AND EXPLOSIVE ROUNDS FOR NON-NUCLEAR MISSILES AND ROCKETS. THIS SRC ALSO APPLIES IN SITUATIONS WHERE THE LAUNCHER TUBES AND EXPLOSIVE ROUNDS, THOUGH NOT IN A READY-TO-FIRE CONFIGURATION, ARE JOINTLY STORED OR TRANSPORTED.
2	HIGH SENSITIVITY (SRC II) - UNCLASSIFIED AA&E. (SEE NOTES (4), (5), AND (6) BELOW).
3	MODERATE SENSITIVITY (SRC III) - UNCLASSIFIED AA&E. (SEE NOTES (4), (5), AND (6) BELOW).
4	LOW SENSITIVITY (SRC IV) - UNCLASSIFIED AA&E. (SEE NOTES (4), (5), AND (6) BELOW).
5	HIGHEST SENSITIVITY (SRC I) - SECRET AA&E. (SEE NOTE (3) BELOW).
6	HIGHEST SENSITIVITY (SRC I) - CONFIDENTIAL AA&E. (SEE NOTE (3) BELOW).
7	CLASSIFIED: ITEMS ASSIGNED A DEMILITARIZATION CODE OTHER THAN A, B, Q, OR P FOR WHICH ANOTHER CIIC IS INAPPROPRIATE. (NOTE: THE LOSS, THEFT, UNLAWFUL DISPOSITION, AND/OR RECOVERY OF AN ITEM WITH CIIC 7 WILL BE INVESTIGATED IN ACCORDANCE WITH DOD-4000-25-2-M AND DOD 7000.14-R, VOLUME 12, CHAPTER 7).
8	HIGH SENSITIVITY (SCR) - CONFIDENTIAL AA&E
9	THIS CODE IDENTIFIES AN ITEM AS A CONTROLLED CRYPTOGRAPHIC ITEM (CCI). CCI IS DESCRIBED AS SECURE TELECOMMUNICATIONS OR INFORMATION HANDLING EQUIPMENT, ASSOCIATED CRYPTOGRAPHIC COMPONENT, OR OTHER HARDWARE ITEM WHICH PERFORMS A CRITICAL COMSEC FUNCTION. ITEMS SO DESIGNATED ARE UNCLASSIFIED BUT CONTROLLED, AND WILL BEAR THE DESIGNATION "CONTROLLED CRYPTOGRAPHIC ITEM OR CCI."
A	CONFIDENTIAL - FORMERLY RESTRICTED DATA
B	CONFIDENTIAL - RESTRICTED DATA
C	MODERATE SENSITIVITY (SRC III) AND LOW SENSITIVITY (SRC IV) - CONFIDENTIAL AA&E. (SEE NOTE (3) BELOW).
D	CONFIDENTIAL - CRYPTOLOGIC
E	SECRET - CRYPTOLOGIC
F	TOP SECRET - CRYPTOLOGIC
G	SECRET - FORMERLY RESTRICTED DATA
H	SECRET - RESTRICTED DATA
I	AIRCRAFT ENGINE EQUIPMENT AND PARTS
J	PILFERAGE - PILFERAGE CONTROLS MAY BE DESIGNATED BY THE CODING ACTIVITY TO ITEMS CODED U (UNCLASSIFIED) BY RECORDING THE ITEM TO J.
K	TOP SECRET - FORMERLY RESTRICTED DATA
L	TOP SECRET - RESTRICTED DATA
M	HANDTOOLS AND SHOP EQUIPMENT
N	FIREARMS PIECE PARTS AND NONLETHAL FIREARMS
O	ITEM CONTAINS NAVAL NUCLEAR PROPULSION INFORMATION; DISPOSAL AND ACCESS LIMITATIONS ARE IDENTIFIED IN NAVSEAINST C5511.32. ALSO, INDENTIFIES UNCLASSIFIED NUCLEAR WEAPONS-RELATED MATERIEL (NWRM) REQUIRING STRINGENT POSITIVE INVENTORY CONTROL IN ACCORDANCE WITH AFMAN 23-110. CAUTION: STORE AND HANDLE IN A MANNER THAT WILL PREVENT UNAUTHORIZED ACCESS TO THIS MATERIAL.
P	AMMUNITION AND EXPLOSIVES
Q	A DRUG OR OTHER CONTROLLED SUBSTANCE DESIGNATED AS A SCHEDULE III, IV, OR V ITEM, IN ACCORDANCE WITH THE CONTROLLED SUBSTANCE ACT OF 1970. OTHER SENSITIVE ITEMS REQUIRING LIMITED ACCESS STORAGE.
R	PRECIOUS METALS, A DRUG OR OTHER CONTROLLED SUBSTANCE DESIGNATED AS A SCHEDULE I OR II ITEM, IN ACCORDANCE WITH THE CONTROLLED SUBSTANCE ACT OF 1970. OTHER SELECTED SENSITIVE ITEMS REQUIRING STORAGE IN A VAULT OR SAFE. (SEE NOTE (1) BELOW).
S	SECRET
T	TOP SECRET
U	UNCLASSIFIED
V	INDIVIDUAL CLOTHING AND EQUIPMENT
W	OFFICE MACHINES
X	PHOTOGRAPHIC EQUIPMENT AND SUPPLIES
Y	COMMUNICATION/ELECTRONIC EQUIPMENT AND PARTS
Z	VEHICULAR EQUIPMENT AND PARTS
    

Code	Definition
0	NON-DETERIORATIVE
1	3 MONTHS
2	6 MONTHS
3	9 MONTHS
4	12 MONTHS
5	18 MONTHS
6	24 MONTHS
7	36 MONTHS
8	48 MONTHS
9	60 MONTHS
A	1 MONTH
B	2 MONTHS
C	3 MONTHS
D	4 MONTHS
E	5 MONTHS
F	6 MONTHS
G	9 MONTHS
H	12 MONTHS
I	72 MONTHS
J	15 MONTHS
K	18 MONTHS
L	21 MONTHS
M	24 MONTHS
N	27 MONTHS
P	30 MONTHS
Q	36 MONTHS
R	48 MONTHS
S	60 MONTHS
T	84 MONTHS
U	96 MONTHS
V	VARIABLE SHELF-LIFE PERIODS OF 90,132,156,192,204,216 AND 228 MONTHS.
W	120 MONTHS
X	MEDICAL ITEMS, PARACHUTES AND CHEMICAL PROTECTIVE CLOTHING WITH A SHELF-LIFE GREATER THAN 60 MONTHS.
Y	180 MONTHS
Z	240 MONTHS
    

Code	Definition
	A BLANK FIELD INDICATES THAT THE ITEM HAS NOT BEEN REVIEWED FOR REPARABLE CHARACTERISTICS.
F	THIS ITEM HAS BEEN REVIEWED AND A DETERMINATION MADE THAT THE ITEM CAN BE RESTORED TO A SERVICEABLE CONDITION FROM AN UNSERVICEABLE CONDITION AT THE ORGANIZATIONAL/FIELD LEVEL.
I	THIS ITEM HAS BEEN REVIEWED AND A DETERMINATION MADE THAT THE ITEM CAN BE RESTORED TO A SERVICEABLE CONDITION FROM AN UNSERVICEABLE CONDITION AT THE INTERMEDIATE LEVEL.
N	THIS ITEM HAS BEEN REVIEWED AND A DETERMINATION MADE THAT THE ITEM CANNOT OR SHOULD NOT BE RESTORED TO A SERVICEABLE CONDITION FROM AN UNSERVICEABLE CONDITION.
R	THIS ITEM HAS BEEN REVIEWED AND A DETERMINATION HAS BEEN MADE THAT THE ITEM CAN BE RESTORED TO A SERVICEABLE CONDITION FROM AN UNSERVICEABLE CONDITION AT THE DEPOT LEVEL.

Code	Definition
A	U.S.ARMY
B	FEDERAL AVIATION ADMINISTRATION
C	U.S. COAST GUARD
D	LEAD SERVICE (MILITARY SERVICE ACTIVITY) - 06 (CONSUMABLE)
F	U.S. AIR FORCE
G	GENERAL SERVICES ADMINISTRATION (CIVIL AGENCIES)
I	INTEGRATED MATERIEL MANAGER
L	LEAD SERVICE - 22 (REPAIRABLE)
M	U.S. MARINE CORPS
N	U.S. NAVY
V	VETERANS ADMINISTRATION (CIVIL AGENCIES)
W	NATIONAL WEATHER SERVICE
X	ABBREVIATED SEGMENT H
    

Code	Definition
A	400.0 
B	300.0 
C	250.0 
D	200.0 
E	175.0 
F	150.0 
G	125.0 
H	110.0 
J	100.2 
K	92.5 
L	90.0 
M	85.0 
N	80.0 
P	77.5 
Q	70.0 
R	65.0 
S	60.0 
T	55.0 
U	50.0 
V	BELOW 50.0 
W	RATING VARIABLE 
X	500.0 
Y	350.0 
Z	NO RATING 
    

Code	Definition
A	400.0 
B	300.0 
C	250.0 
D	200.0 
E	175.0 
F	150.0 
G	125.0 
H	110.0 
J	100.2 
K	92.5 
L	90.0 
M	85.0 
N	80.0 
P	77.5 
Q	70.0 
R	65.0 
S	60.0 
T	55.0 
U	50.0 
V	BELOW 50.0 
W	RATING VARIABLE 
X	500.0 
Y	350.0 
Z	NO RATING 
    

Code	Definition
1	AIRCRAFT ENGINE, INTERNAL COMBUSTION ENGINES AND FUEL CONTROL DEVICES
2	TYPE CARGO CODE NOT APPLICABLE (FOR AIR FORCE INTERNAL USE)
3	ELECTROSTATIC SENSITIVE DEVICE (ESD), SUBJECT TO DAMAGE CAUSED BY ELECTROSTATIC DISCHARGE. (SEE DOD 4500.32-R, VOLUME 1, APPENDIX A, SECTION I FOR ADDITIONAL INFORMATION ON ESD DEVICES)
4	RADIOACTIVE MATERIAL (NO LABEL REQUIRED)
A	RADIOACTIVE SUBSTANCES, UN CLASS 7 (RADIOACTIVE LABEL)
B	MIXED HAZARDOUS MATERIALS - CONSOLIDATED ONLY AS AUTHORIZED BY COAST GUARD REGULATIONS, TITLE 49 CFR, USE WITH T-2 OR T-3 DOCUMENTS ONLY
C	ETIOLOGIC AGENT, UN CLASS 6 (ETIOLOGIC LABEL)
D	CONTAMINATED CARGO (NOT INCLUDING ANY HAZARDOUS MATERIAL)
E	EMPTY HAZARDOUS MATERIAL CONTAINERS OR PACKAGES (EMPTY LABEL)
F	EXPLOSIVES, CLASS C, UN CLASS 1 (EXPLOSIVE C LABEL)
G	NONFLAMMABLE COMPRESSED GAS, UN CLASS 2 (NONFLAMMABLE GAS LABEL; EXCEPT: (1) OXYGEN REQUIRES AN OXIDIZER LABEL, AND (2) FLUORINE REQUIRES POISON AND OXIDIZER LABELS)
H	SUBJECT TO DAMAGE FROM HEAT
I	EXPLOSIVES, CLASS A, UN CLASS 1 (EXPLOSIVE A LABEL)
J	EXPLOSIVES, CLASS B, UN CLASS 1 (EXPLOSIVE B LABEL)
K	SPONTANEOUSLY COMBUSTIBLE SUBSTANCES, UN CLASS 4 (SPONTANEOUSLY COMBUSTIBLE LABELS AND FLAMMABLE SOLID LABELS)
L	WATER REACTIVE SUBSTANCES, UN CLASS 4 (FLAMMABLE SOLID LABELS AND DANGEROUS-WHEN-WET LABELS)
M	MAGNETIC MATERIAL
N	DANGEROUS MATERIEL IN LIMITED QUANTITIES (NO LABEL REQUIRED)
O	FLAMMABLE COMPRESSED GAS, UN CLASS 2.1 (FLAMMABLE GAS LABEL)
P	POISON, CLASS B, UN CLASS 6 (POISON LABEL)
Q	SUBJECT TO DAMAGE FROM FREEZING
R	FLAMMABLE LIQUIDS, UN CLASS 3 (FLAMMABLE LIQUIDS LABEL)
S	POISONS, CLASS A, UN CLASS 2 (POISON GAS LABEL) OR UN CLASS 6 (POISON LABEL)
T	POISON, CLASS C, UN CLASS 6 (IRRITANT LABEL)
U	COMBUSTIBLE LIQUIDS (NO LABEL)
V	MISCELLANEOUS HAZARDOUS MATERIALS, UN CLASS 9 (NO LABEL)
W	CORROSIVE MATERIALS, UN CLASS 8 (CORROSIVE LABEL)
X	FLAMMABLE SOLIDS, UN CLASS 4 (FLAMMABLE SOLID LABEL)
Y	OXIDIZING MATERIALS, UN CLASS 5 (OXIDIZER OR ORGANIC PEROXIDE LABEL)
Z	NO SPECIAL TYPE OF CARGO CODE APPLICABLE

Code	Definition
1	AIRCRAFT ENGINE, INTERNAL COMBUSTION ENGINES AND FUEL CONTROL DEVICES
2	TYPE CARGO CODE NOT APPLICABLE (FOR AIR FORCE INTERNAL USE)
3	ELECTROSTATIC SENSITIVE DEVICE (ESD), SUBJECT TO DAMAGE CAUSED BY ELECTROSTATIC DISCHARGE. (SEE DOD 4500.32-R, VOLUME 1, APPENDIX A, SECTION I FOR ADDITIONAL INFORMATION ON ESD DEVICES)
4	RADIOACTIVE MATERIAL (NO LABEL REQUIRED)
A	RADIOACTIVE SUBSTANCES, UN CLASS 7 (RADIOACTIVE LABEL)
B	MIXED HAZARDOUS MATERIALS - CONSOLIDATED ONLY AS AUTHORIZED BY COAST GUARD REGULATIONS, TITLE 49 CFR, USE WITH T-2 OR T-3 DOCUMENTS ONLY
C	ETIOLOGIC AGENT, UN CLASS 6 (ETIOLOGIC LABEL)
D	CONTAMINATED CARGO (NOT INCLUDING ANY HAZARDOUS MATERIAL)
E	EMPTY HAZARDOUS MATERIAL CONTAINERS OR PACKAGES (EMPTY LABEL)
F	EXPLOSIVES, CLASS C, UN CLASS 1 (EXPLOSIVE C LABEL)
G	NONFLAMMABLE COMPRESSED GAS, UN CLASS 2 (NONFLAMMABLE GAS LABEL; EXCEPT: (1) OXYGEN REQUIRES AN OXIDIZER LABEL, AND (2) FLUORINE REQUIRES POISON AND OXIDIZER LABELS)
H	SUBJECT TO DAMAGE FROM HEAT
I	EXPLOSIVES, CLASS A, UN CLASS 1 (EXPLOSIVE A LABEL)
J	EXPLOSIVES, CLASS B, UN CLASS 1 (EXPLOSIVE B LABEL)
K	SPONTANEOUSLY COMBUSTIBLE SUBSTANCES, UN CLASS 4 (SPONTANEOUSLY COMBUSTIBLE LABELS AND FLAMMABLE SOLID LABELS)
L	WATER REACTIVE SUBSTANCES, UN CLASS 4 (FLAMMABLE SOLID LABELS AND DANGEROUS-WHEN-WET LABELS)
M	MAGNETIC MATERIAL
N	DANGEROUS MATERIEL IN LIMITED QUANTITIES (NO LABEL REQUIRED)
O	FLAMMABLE COMPRESSED GAS, UN CLASS 2.1 (FLAMMABLE GAS LABEL)
P	POISON, CLASS B, UN CLASS 6 (POISON LABEL)
Q	SUBJECT TO DAMAGE FROM FREEZING
R	FLAMMABLE LIQUIDS, UN CLASS 3 (FLAMMABLE LIQUIDS LABEL)
S	POISONS, CLASS A, UN CLASS 2 (POISON GAS LABEL) OR UN CLASS 6 (POISON LABEL)
T	POISON, CLASS C, UN CLASS 6 (IRRITANT LABEL)
U	COMBUSTIBLE LIQUIDS (NO LABEL)
V	MISCELLANEOUS HAZARDOUS MATERIALS, UN CLASS 9 (NO LABEL)
W	CORROSIVE MATERIALS, UN CLASS 8 (CORROSIVE LABEL)
X	FLAMMABLE SOLIDS, UN CLASS 4 (FLAMMABLE SOLID LABEL)
Y	OXIDIZING MATERIALS, UN CLASS 5 (OXIDIZER OR ORGANIC PEROXIDE LABEL)
Z	NO SPECIAL TYPE OF CARGO CODE APPLICABLE
    

Code	Definition
1	NOT TO BE ASSIGNED 
2	CLASSIFIED 
3	RESERVED 
4	PROTECTED (SENSITIVE) 
5	PROTECTED (PILFERABLE) 
6	PROTECTED (CONTROLLED) 
7	UNASSIGNED 
8	UNASSIGNED 
9	NO SPECIAL HANDLING REQUIRED EXCEPT AS INDICATED BY I, R, OR Z
B	CLASSIFIED HEAVY LIFT (HL)
C	RESERVED HEAVY LIFT (HL)
D	PROTECTED (SENSITIVE) HEAVY LIFT (HL)
E	PROTECTED (PILFERABLE) HEAVY LIFT (HL)
F	PROTECTED (CONTROLLED) HEAVY LIFT (HL)
G	UNASSIGNED HEAVY LIFT (HL)
H	UNASSIGNED HEAVY LIFT (HL)
I	NO SPECIAL HANDLING REQUIRED HEAVY LIFT (HL)
K	CLASSIFIED OUTSIZED DIMENSIONS (OD)
L	RESERVED OUTSIZED DIMENSIONS (OD)
M	PROTECTED (SENSITIVE) OUTSIZED DIMENSIONS (OD)
N	PROTECTED (PILFERABLE) OUTSIZED DIMENSIONS (OD)
O	PROTECTED (CONTROLLED) OUTSIZED DIMENSIONS (OD)
P	UNASSIGNED OUTSIZED DIMENSIONS (OD)
Q	UNASSIGNED OUTSIZED DIMENSIONS (OD)
R	NO SPECIAL HANDLING REQUIRED OUTSIZED DIMENSIONS (OD)
S	CLASSIFIED HL & OD
T	RESERVED HL & OD
U	PROTECTED (SENSITIVE) HL & OD
V	PROTECTED (PILFERABLE) HL & OD
W	PROTECTED (CONTROLLED) HL & OD
X	UNASSIGNED HL & OD
Y	UNASSIGNED HL & OD
Z	NO SPECIAL HANDLING REQUIRED HL & OD

Code	Definition
A	SHIPMENT DOES NOT EXCEED 72" IN ANY DIMENSION (LENGTH, WIDTH, OR HEIGHT)
C	CONSOLIATED SHIPMENTS (SHIPMENTS OF MULTIPLE REQUISITIONS) DOES NOT EXCEED 72" IN ANY DIMENSION (LENGTH, WIDTH, OR HEIGHT)
D	CONSOLIATED SHIPMENTS (SHIPMENTS OF MULTIPLE REQUISITIONS) WITH MEASUREMENTS GREATER THAN 72" IN ANY DIMENSION (LENGTH, WIDTH, OR HEIGHT)
Z	SHIPMENT DOES EXCEED 72" IN ANY DIMENSION (LENGTH, WIDTH, OR HEIGHT)

Code	Definition
A	SAMPLED; FREIGHT CLASSIFICATION DATA CORRECT.
B	SAMPLED; FREIGHT CLASSIFICATION DATA (FCD) DEVELOPED BY SDDC; MILSTAMP DEVELOPED PRIOR TO SDDC SAMPLING AND SHOULD BE REVIEWED; FCD CANNOT BE CHANGED EXCEPT BY SDDC.
C	SAMPLED; FREIGHT CLASSIFICATION DATA (FCD) DEVELOPED BY SDDC; MILSTAMP DEVELOPED AFTER SDDC SAMPLING; FCD CANNOT BE CHANGED EXCEPT BY SDDC.